CORSAIR DOMINATOR 32GB (4 x 8GB) 240-Pin DDR3 SDRAM DDR3 1600 Desktop Memory Model CMP32GX3M4X1600C10

Pros: I have it running at 1666 at 1.6 volts on a eVGA X58 motherboard.

Cons: Maybe it is just my batch but this ram is very touchy when it comes to timings. For some reason my ram will not run at the timings listed. It is running at 11-12-11-24 and tRFC at 150 @1T command rate.

I have tried increasing voltage but it will not post but like i said it just might be a bad batch because i took each one out and not 1 will run at the listed timings in the spec sheet.

Pros: I purchased 3 sets of these for an SR-2 computational server. These have been rock solid and look great!

Cons: 1333 mhz but I knew that going in. When one mounts the motherboard vertically the heatsink fans can slide off even when over tightened

Other Thoughts: I am happy with my purchase but I do not use the included heatsink fans

Pros: Very stable, no issues running at 1600mhz so far. The slightly slower timings are a trade-off of sorts for increased stability.

Cons: They're taller than normal sticks, make sure they'll fit in your build. (I didn't have any issues, but keep it in mind.)

Other Thoughts: I had 3 of them in a socket 1366 board with a Core i7 920 for a short while. I could run that at 1600mhz without any issue. Before, I had 6GB of Corsair XMS3 that would have occasional issues under heavy load running at 1600mhz. Could be related to the slower timing on this ram, but I can't say for sure (XMS3 sticks were 8-8-8-24). They are now in a socket 2011 build and I have not had a single issue so far.

Pros: I had Dominator with my other board, and had excellent performance. It's a top-of-the-line memory choice. Even the Web site is well designed, and a pleasure to use to select your memory.

Cons: The Dominator series has high cooling fins. On my last board I had to replace my CPU heat sink fan, because it didn't have any clearance. I had to get one where the fan and fins were lined up vertically. In this install I'm using a water cooler - Corsair H80. I had the same problem because this board (Asrock X79 Pro) has memory slots on both sides of the CPU. The ones on the left didn't allow room for the cooler radiator to be installed against the back of the case as it was hitting the fins. I could have left it there, but there would have been pressure on one of the DIMS. And I have a Thermaltake Xaser VI, which is huge.

Pros: Installed on DX79SI board. Works as advertised on 1600 XMP. Solid performance.

Cons: Price, but you get what you pay for...

Pros: No hickups and performs very well

Cons: with heatsinks installed just barely clears heatsinks on lga 2011 mobos

Pros: Works great so far in my ASUS Sabertooth 990FX. 24-hour burn in showed no issues.

Cons: A tad higher than my previous Corsair DIMMs. That combined with the slightly-closer proximity of the DIMM slots to the CPU socket caused a minor conflict with the CPU heat sink fan. Resolved by removing the fan guard.

Pros: Way more then enough memory I could ever use!!

Handle very well never had any issues even when under stress test

Cons: N/A

Other Thoughts: Corsair 800DW
Corsair HX1050
Corsair Dominator 32gb 1600mhz
Corsair H100 Watercool
Corsair Force GT 240GB
Asus Rampage IV Extreme
Intel I7 3930k Processor
Evga Nvidia GTX570HD Classified

Pros: Almost did not fit in my case with a push and pull H100.

Cons: None

Other Thoughts: Current Build:
http://secure.newegg.com/Shopping/AddToCart.aspx?Submit=ADD&ItemList=35-553-002%7c4%2c19-116-492%7c1%2c35-608-008%7c1%2c27-118-049%7c1%2c14-130-683%7c1%2c17-151-087%7c1%2c13-157-290%7c1%2c11-352-007%7c1%2c20-233-229%7c1%2c20-171-567%7c2%2c35-181-017%7c1%2c12-816-074%7c1

Pros: Stress tests show works fine at 1600. Defaulted to 1333 until I set up XMP profile in MB Bios. I don't know if this memory is better the the Corsair Vengeance series but I wanted the best stability and was willing to pay a bit of of premium for this. Photoshop CS5 64 does take advantage of the memory and this does speed up image processing.

Cons: None really. I just needed to learn how to apply XMP profile in Bios.

Other Thoughts: NEW BUILD
Intel BOXDZ68BC LGA 1155 Intel Z68 Motherboard
Intel Core i7-2700K Sandy Bridge 3.5GHz (3.9GHz Turbo) LGA 1155
CORSAIR DOMINATOR 32GB (4 x 8GB) DDR3 1600 CMP32GX3M4X1600C10
EVGA SuperClocked 01G-P3-1363-KR GeForce GTX 460 (Fermi) Video
Crucial M4 CT256M4SSD2 2.5" 256GB SATA III Solid State Drive (SSD)
SeaSonic X750 Gold 750W Power Supply
LIAN LI PC-9F Black Aluminum ATX Mid Tower Computer Case
StarTech PLATE9MHD 9 Pin Serial Male to 10 Pin IDC Motherboard Header
BYTECC Bracket-35225 2.5 Inch HDD/SSD Mounting Kit
LITE-ON 24X DVD Writer Black SATA Model iHAS424-98
LITE-ON Blu-ray Burner with 3D Playback SATA iHBS212-08
Microsoft Windows 7 Ultimate SP1 64-bit - OEM