Pros: My laptop cpu was at 150 degrees farenheight running very slow. Now after using this Zalman paste its at 111 degrees farenheight. (: Computer runs a lot faster.

Cons: none

Pros: Easy to apply (once you get it to thin out) , no mess

Cons: Not much in bottle, not sure how some people got 8-10 uses, I did 2 processors and two video cards and the bottle was done, also the first two bottles I opened had the same issue, the compound was almost dried up (in the bottom of the bottle no less) but if you soak the bottle in a cup or container of some sort with fairly hot water for about 10-15 minutes it becomes fairly easy to use. The brush itself seems like it could have stood to be just a bit longer so it can reach the bottom of the container, I had to use a Q-tip to get full use out of a bottle. My only other thought would be that if I ordered it again it would have to be if it was shipped by other means than the USPS

Other Thoughts: They should put suggestions on the packaging on how to get the compound to loosen up. I'd also have to say they should consider finding another way to weigh this product, I honestly can't believe that there's 3.5g in the bottles when they appear close to empty when you open them. I think I would have given it a higher rating if it had more in the bottle and had not been close to being dried up.

Pros: easy to use

Cons: wierd odor as it cures heats up, after 3 days odor gone

Pros: Does what it is supposed to do.

Cons: My bottle came kind of dry and was hard to get enough product onto the cpu, fortunately I got just enough out.

Pros: sadly no pros anymore

Cons: - As thick as other paste but stickier than most.
- Can't even retrieve stuff from the bottle.

Other Thoughts: This used to be my favourite paste by far due to it's ease of use. It was easier to apply than standard paste and you didn't have to fear of using too much : it didn't have any consequence if you did. It was the best choice IMO for a guy like me with limited experience applying paste. However, the last two bottles I got (one several weeks ago and another one last year) where unusable. The paste had become so thick and sticky that I could not even retrieve all of it from the bottle. Applying the sticky goo on the CPU was a total mess leading to abysmal results in the heat department. Either they changed the recipe, it's too sensible to cold temperature or the it has a short shelf life.

Manufacturer Response:

Dear valued customer,

We sincerely apologize for the issue. Please contact our customer service e-mail support.usa@zalmanusa.com or via toll free number 1-888-925-6266 for further assistance.

Thank you.

Best regards,

Zalman USA Customer Service

Pros: As always, this is highly recommended paste, easy application, great temps, easy to store and reuse.

Cons: The applicator stem is too short, leaving nearly half of the product unreachable. Had to go buy a separate brush to get the remaining out. Also, while the weight may be correct (unsure), the bottle usually comes about 1/3 full, so you may get one or two applications (YES, I know how much to use), before having to figure out how to get to the rest at the bottom of the bottle.

Other Thoughts: Good purchase, would recommend, just be prepared to be slightly frustrated trying to get it all out. I liken the experience to a bottle of A1 sauce. Superb quality, love using it, but it is a strain trying to get the last of it out of the bottle when it runs low.

Pros: Much better value than single use packages. What are they thinking? Only building one computer? For about the same price as a single-use package, this one has 3 1/2 grams of grease, so it can stored and reused on my next build.

Cons: None.

Pros: Ridiculously easy application, great control, even coating.

Cons: Tiny amount of compound. Just barely enough for one application to 2 surfaces.

Other Thoughts: Like tons of other reviewers, I love the ease of application of the compound. Got a nice even coat on both surfaces (CPU & Cooler Block). It does what it says, solid connection for heat transfer. My temps are 16° C. at idle and no more than 40° C. when tasking the CPU.
Wish I had more of the stuff for future applications. Hear that, Zalman?

Pros: Applied paste to approximately 5-7 cpus and I still have PLENTY for more. I think some reviews that mention that there isn't enough paste in the bottle.. they apply too much. Either way, it does it's job and does it well.

Love the brush

Cons: None

Pros: Applied and temps dropped 6-8 celsius from stock paste. Easy to apply and it doesn't have a cure time... 43-47Celsius to 34-37

Cons: Not much in the jar it was only enough for a am3+ socket processor and a Nvidia gtx 660

Other Thoughts: I was a bit stumbled when I realized it came like fingernail polish figured I'd give it a try anyways the temp drops made it well worth and applying with a brush is kind of fun