Question 1

Can this case fit a EK CoolStream XE 360 rad in the front of the case ?

Accepted Answer

Might add, for top mount, if you're in "push" setup with 140mm fans mounted on bottom of 140WD rad, gets a little tight running the PCI power cable(s) out the back.  Would not be an issue on a 240/360 rad with 120 fans.  I have build pics should you need, on vacation through Saturday, however.

Question 2

The case is huge. Does it support 200mm fans on top and front? They are not listed, yet they list radiators even wider than 200mm.

Accepted Answer

The front is tight but the top you can place a 200 mm not by default as the top supports 120/140 x3 as the front does . The 200mm fan is about 7.87x7.87 x1 1/2 . I don’t see it fitting it might mounted inside the top but I don’t see it happening on the front. My other cosmos I case has a 200 mm in front but is much wider or at least looks wider.  I too am still looking into adding 2 200mm to top and will more than likely buy a 200 to see if it fits. Remember the radiator dimension on the largest radiator supported is still a 140 mm width and uses 140 mm fans for cooling . Hope this helps

Question 3

Are you able to install the 3.5 hhd in the back of the case or are you stuck installing them in the front? Thank you

Accepted Answer

No 3.5"  spaces in the back.  3.5" drive trays (2 furnished with case, additional sold separately) mount on vertical rails in the front of the case (to the right of CPU/RAM/PCIe), either above or below the PSU shroud.  Awesome case, but not entirely friendly to multiple 3.5" HDDs.  Personally have 2x M.2 SSDs RAID0 system drive and 3x 3.5" enterprise class storage HDDs, with (2) of the (3) 3.5" mounted above the shroud (exposed).  Needed a roomy case WITH a 5.25" bay, able to handle EATX, *.coolers, and multiple 3.5" drives (i.e., fully customizable).  Bucked up for this one, was not disappointed.

Question 4

Good day !!! Please tell me which MSI MEG ACE z390 connector on the motherboard is suitable for the MB-A-rgb sync Cooler master 700M connector for synchronization?

Accepted Answer

The 700m comes with a decent fan and lighting controller built in but if u want bypass the controller and use software or connect to your mobo the case uses the standard 5v 3 pin a-rgb header, the connecter on your mother board is labled jrainbow1 and is on page 44 of the online manual, the plug itself is on the bottom left of your motherboard

Question 5

Is it release day?

Accepted Answer

Yes But only to select venders like Newegg

Question 6

What types of motherboards can I use with the Cooler Master COSMOS C700M case?

Accepted Answer

The Cooler Master COSMOS C700M case is compatible with Mini-ITX, Micro-ATX, ATX, and E-ATX motherboards (supporting up to 12.00" x 10.70").

Question 7

What kind of ports are available on the front panel of this case?

Accepted Answer

The front panel of this case includes 1 x USB 3.1 Type-C, 4 x USB 3.0 Type-A, 2 x Audio ports, a Fan Speed Control Button, and an ARGB Control Button.

Question 8

What is the maximum size of the GPU that this case can accommodate?

Accepted Answer

The maximum GPU length that this case can accommodate is 490 mm without the 3.5" HDD bracket, and 320 mm with the 3.5" HDD bracket.

Question 9

What are the cooling options for this particular case?

Accepted Answer

The cooling options for this case include top mounting for up to 3 x 120/140mm fans, front mounting for up to 3 x 120/140mm fans, rear mounting for 1 x 120/140mm fan, and bottom mounting for up to 2 x 120/140mm fans (bracket needed).

Question 10

How many drives can this case hold, and what are the sizes?

Accepted Answer

This case can hold up to 5 drives: (4 + 1) x Combo 3.5" / 2.5".

Questions & Answers