BEEYUIHF Soldering Flux with Desoldering wick Electronics Repairs Remover Kit
BEEYUIHF Electronics Soldering Repairs Cleaning Kit, including 1Piece 10cc/10g syringe No-Clean soldering flux paste #9530 and 1 piece 3M/10ft 2.5mm desoldering wick braid. Soldering Flux plus desoldering wick increases mutually activity and speeds up the cleaning of solder joints.
Soldering flux and Desoldering wick Braid - A Good Partner for Soldering Repairs
- BEEYUIHF brand flux and solder wick soldering kit, suitable for electronic soldering, repair and rework. All-round cleaning of PCB boards and solder joints, suitable forelectronic components soldering, SMT repair, BGA chip, etc.
#9530 No-Clean soldering flux paste with 3M/10ft 2.5mm Desoldering wick Braid
Desoldering wick and solder flux utilize each other's properties to complement each other, and flux can double the effectiveness of the tape for brilliant soldering and rework results.
Application of Soldering Paste Flux with Desoldering wick in Repair:
Apply flux evenly to the pins
flux for soldering helps to separate and evenly tin the pins, making them shiny and full.Excellent wettability, non-conductive, non-sticky residue.
Dissolved tin on the pins
Drag soldering is to apply flux evenly on the board and IC pins and drag the solder in one direction after the solder is completely melted.
Absorb tin from IC patches
After disassembling the IC with the hot air gun, use the tin suction tape to absorb the residual tin and keep the IC board clean.
Removal of blocked hole in PCB
Solder wick removes minor defects during repairs, clears clogged holes, removes excess tin, unavoidable minor faults in everyday soldering.
Oxidation resistivity and anti-corrosion protection,good thermal conductivity.
The Braided Desoldering wicks are made of 100% copper wires with a fine braid design, fast heat conduction, suitable for rapid tin suction, not only improving work efficiency and quality, but also more clean. Speed up the speed of absorbing tin and low residue of flux.
Desoldering wick braid for repairing minor defects, cleaning circuit boards.
Desoldering wire reduces the time required for reworking/repairing electronic products and greatly reduces the risk of thermal damage to the circuit board. Solder wick is suitable for areas with dense pins and for soldering work such as desoldering integrated circuits and SMD multi-pin components.
BEEYUIHF Soldering Flux with Desoldering wick Electronics Repairs Remover Kit
BEEYUIHF Electronics Soldering Repairs Cleaning Kit, including 1Piece 10cc/10g syringe No-Clean soldering flux paste #9530 and 1 piece 3M/10ft 2.5mm desoldering wick braid. Soldering Flux plus desoldering wick increases mutually activity and speeds up the cleaning of solder joints.
Soldering flux and Desoldering wick Braid - A Good Partner for Soldering Repairs
- BEEYUIHF brand flux and solder wick soldering kit, suitable for electronic soldering, repair and rework. All-round cleaning of PCB boards and solder joints, suitable forelectronic components soldering, SMT repair, BGA chip, etc.
#9530 No-Clean soldering flux paste with 3M/10ft 2.5mm Desoldering wick Braid
Desoldering wick and solder flux utilize each other's properties to complement each other, and flux can double the effectiveness of the tape for brilliant soldering and rework results.
Application of Soldering Paste Flux with Desoldering wick in Repair:
Apply flux evenly to the pins
flux for soldering helps to separate and evenly tin the pins, making them shiny and full.Excellent wettability, non-conductive, non-sticky residue.
Dissolved tin on the pins
Drag soldering is to apply flux evenly on the board and IC pins and drag the solder in one direction after the solder is completely melted.
Absorb tin from IC patches
After disassembling the IC with the hot air gun, use the tin suction tape to absorb the residual tin and keep the IC board clean.
Removal of blocked hole in PCB
Solder wick removes minor defects during repairs, clears clogged holes, removes excess tin, unavoidable minor faults in everyday soldering.
Oxidation resistivity and anti-corrosion protection,good thermal conductivity.
The Braided Desoldering wicks are made of 100% copper wires with a fine braid design, fast heat conduction, suitable for rapid tin suction, not only improving work efficiency and quality, but also more clean. Speed up the speed of absorbing tin and low residue of flux.
Desoldering wick braid for repairing minor defects, cleaning circuit boards.
Desoldering wire reduces the time required for reworking/repairing electronic products and greatly reduces the risk of thermal damage to the circuit board. Solder wick is suitable for areas with dense pins and for soldering work such as desoldering integrated circuits and SMD multi-pin components.