Dash Cam OBD Hardwire Kit, Dash Camera USB Type C Hardwire Kit with OBD2 Power Cable for Dashcam 12-24V to 5V/3A with Low Voltage Protection 24h Parking Surveillance/ACC Mode for Dashcam, GPS or Radar

[24h Parking / ACC Mode Switch]: " MODE -": will active your dashcam parking mode for 24h Surveillance and power will cut off if voltage drops below 11.6V; " MODE O": will active ACC mode which only supplier power when engine is on
[Dash Cam OBD2 Hardwire Kit]: This OBD II dash cam hard wire power charging cable kit is a model for most car dash cameras, GPS, radar, and dash cams on the market (Please note that this unit DOES NOT work with EV Car/Electric Vehicle)
[Simple Plug-in Installation]: The OBD2 dash cam hardwire cable is easy to install by plugging it into your car's OBD connector and making sure it can power on your dashcam, then hide the extra wire; unlike other complex hardwire kits, you need to deal with fusebox and battery electricity
[Low voltage protection]: It has a smart low voltage protection system that will automatically shut off the power to your dash cam when the battery voltage drops to 11.6V or 23.2V, thus preventing it from draining the battery
[Clean and Space Saving]: By using this dash cam OBD 2 hardwire kit you can easily hide the wire and cable to make your carpet looks cableless and clean; also this dash cam charger doesn't occupy your car's cigarette lighter port and allow you can use the port to charge other devices in your car.
[Question 1: Does Not Power Off]: The ACC Mode"0", the OBD2 hardwire kit will power off in 20 minutes after the car engine is off(Time delay setup to provide power for car start/stop function)

All Types of Dashcam Hardwire
How we start?
We start with a dashcam accessories supplier, and we decided to develop the dashcam hardwire kit with more functions to meet customers' new requirements, and we started to do so.
Why the hardwire kit cannot cut off power when engine is off?
Because nowadays many vehicles have the start/stop function, the hardwire kit has the time delay function to keep the power supply when engine is for a temporary stop
Why the hardwire kit is not compatible with all brand dashcams?
Because the Type-C uses a different ACC signal port than others (A5-B5 or A8-B8) it may cause not compatible issue.

OBD2 DASHCAM HARDWIRE KIT

SPECIFICATIONS:

Voltage Input: 12V-24V | Output: 5V/3A
Length: 3.5meters(11.5 ft.)
Connector Type: USB Type C

COMPATIBILITY:

The OBD charger cable is design for majority dash camera, GPS, radar detection and other electronic devices with USB Type-C connector.

This unit does not work with Electric Vehicles and Plug-In Hybrid vehicles.

Mode “0”: The OBD kit will power off in 20 minutes when car engine is off.

voltage protection

BATTERY PROTECTION

The dash cam hardwire kit will cut off the power when the battery voltage gets too low.

install

PLUG & GO

Plug into the car's OBD slot.
Connect to the dashcam.
Test the power supply and parking mode function.
Hide the extra wires.

dchww970-600

PARKING MODE / ACC MODE

You can choose different modes by a simple switch based on your parking environment.
We do recommend using the ACC mode for long-time parking.

PRESS TO SWITCH 2 MODES:

Mode “0”:

ACC mode: When your car ACC is off, the OBD hardwire cable will power off in 20 minutes when car engine is off.

Mode “—”:

Parking Surveillance mode: When your car ACC is off, the OBD power cable will keep working until detecting the car battery voltage is at 11.6V(low voltage protection).

The low voltage protection for mode “—” protects your car from running out of the battery, and keep enough voltage to start the car for the next driving.