Your Browsing History
Meet Your Seller
Digital Temperature Controller Dual Probe Reptile Thermostat Controlled Outlet for Terrarium Heat Mat Heating Pad, Switch Cooling Fan Freezer Fridge ON & Off at Setpoints 10A 1200W
- Think different, think simpleYou are able to set every outlet(attached to heater/fan) to turn on at a certain temp, and turn off at another temp
- 2 controllers in one unitTwo outlets are individually separate, each supports heating & cooling. With two waterproof sensors, you can set different temps to control different areas, such as with 2 heat lamps/mats for dual zones or even for 2 tanks
- Safe and reliableHigh and low temperature alarm, and temperature difference alarm, keep your target secure
+
+
Overview
Reviews
Any questions? Our AI beta will help you find out quickly.
Try me now
Convert freezer to refrigeratorWith Power-On delay, it can protect compressor from frequent ON-OFF
Widely usedIt is used as temperature switches / thermostatically controlled outlet for heat mat / heat lamp / heating pad of reptile terrarium / tank, aquarium heater / chiller, greenhouse and grow tent heater, garage / attic exhaust fan, breeding, seedling and fermentation
1. How control temperature?
Temperature controller is actual Heating/Cooling controller, thus MUST SET ON-Temp to turn ON Heating/Cooling, and MUST SET OFF-Temp to turn OFF Heating/Cooling.
Heating starts at LOW Temp [ON-Temp(1oN, 2oN)], stops at HIGH Temp [OFF-Temp(1oF, 2oF)], thus for heating MUST SET 1oN (2oN) LESS than 1oF (2oF);
In heating mode, 1oN (2oN) is the minimum temp you allow, 1oF (2oF) is the maximum temp you allow.
Cooling starts at HIGH Temp [ON-Temp(1oN, 2oN)], stops at LOW Temp [OFF-Temp(1oF, 2oF)], thus for cooling MUST SET 1oN (2oN) GREATER than 1oF (2oF).
In cooling mode, 1oN (2oN) is the maximum temp you allow, 1oF (2oF) is the minimum temp you allow.
2. Reading temp is inaccurate?
Every controller is calibrated before come out of factory, it is reading temp accurately!
Please don't compare it to common inaccurate thermostatthermometer or temp gun. If you doubt controller accuracy, please calibrate with ice-water mixture (it is 32F when ice is melting), and you will see which device is accurate then.
3. Beeper keeps sounding?
Probably it is the Alarm settings ( ALAHd7 ) you set are NOT the right temperature you want. AL is low temperature alarm (it sounds when current temp is AL or Lower), AH is high temperature alarm (it sounds when current temp is AH or Higher), d7 is difference alarm (it sounds when the temp deviation between sensor 1 and sensor 2 is over d7). If you don't need alarm function, please don't change the values of ALAHd7, the default values usually won't trigger alarm. You can factory reset by switching temp unit from F to C in setting.
Please download User Manual PDF in Product information.
Widely usedIt is used as temperature switches / thermostatically controlled outlet for heat mat / heat lamp / heating pad of reptile terrarium / tank, aquarium heater / chiller, greenhouse and grow tent heater, garage / attic exhaust fan, breeding, seedling and fermentation
1. How control temperature?
Temperature controller is actual Heating/Cooling controller, thus MUST SET ON-Temp to turn ON Heating/Cooling, and MUST SET OFF-Temp to turn OFF Heating/Cooling.
Heating starts at LOW Temp [ON-Temp(1oN, 2oN)], stops at HIGH Temp [OFF-Temp(1oF, 2oF)], thus for heating MUST SET 1oN (2oN) LESS than 1oF (2oF);
In heating mode, 1oN (2oN) is the minimum temp you allow, 1oF (2oF) is the maximum temp you allow.
Cooling starts at HIGH Temp [ON-Temp(1oN, 2oN)], stops at LOW Temp [OFF-Temp(1oF, 2oF)], thus for cooling MUST SET 1oN (2oN) GREATER than 1oF (2oF).
In cooling mode, 1oN (2oN) is the maximum temp you allow, 1oF (2oF) is the minimum temp you allow.
2. Reading temp is inaccurate?
Every controller is calibrated before come out of factory, it is reading temp accurately!
Please don't compare it to common inaccurate thermostatthermometer or temp gun. If you doubt controller accuracy, please calibrate with ice-water mixture (it is 32F when ice is melting), and you will see which device is accurate then.
3. Beeper keeps sounding?
Probably it is the Alarm settings ( ALAHd7 ) you set are NOT the right temperature you want. AL is low temperature alarm (it sounds when current temp is AL or Lower), AH is high temperature alarm (it sounds when current temp is AH or Higher), d7 is difference alarm (it sounds when the temp deviation between sensor 1 and sensor 2 is over d7). If you don't need alarm function, please don't change the values of ALAHd7, the default values usually won't trigger alarm. You can factory reset by switching temp unit from F to C in setting.
Please download User Manual PDF in Product information.
Warranty & Returns
Warranty, Returns, And Additional Information
Warranty
- Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
- CONTACT
Return Policies
- Return for refund within: 30 days
- Return for replacement within: 30 days
- This item is covered by Grandwood Tech Limited Return Policy
Manufacturer Contact Info
- For a directory of all our manufacturers, please click below.
- Manufacturers Directory
LOADING...