VELIMAX 1/2-inch Frosted Reeded Glass Window Film is designed to give a beautiful appearance of modern appearance to your windows and doors, whether for privacy, to block out an unsightly view or for decorative purposes.
Besides prevent UV rays, it can also cut out a large proportion of the unwanted glare, whilst still allowing natural light to pass through. It will work on any smooth glass surface and can be used anywhere in the home, requires no additional cleaning and can be installed at a fraction of the cost.
Fancy and Stylish
Freshen up your windows and create a relaxing atmosphere to your home.
Privacy and Sunlight
Misshapes the view and limits while enabling a lot of light to go through.
Reduce Glare
Blocks UV rays by 99% and reduces the fading and aging of the furnishings.
Easy to Install
Measure Glass?Clean Glass?Cut Film?Remove Liner?Spray Water?Hang Film?Squeegee Film?Trim Edges
Suitable for all kinds of smooth and flat glass surfaces.
It's a smart choice to embellish your room by adding style and concealing an undesirable view seen through a window.
How to remove the air bubbles?
Use a plastic card to squeegee air bubbles and water. If it's hard to get rid of the bubbles, uncover the window film, spray more water between the glass and the film and squeegee firmly again. Water will make it much easier to remove bubbles.
Any tips to peel off the protective liner?
Attach 2 pieces of transparent tape to the front andback surfaces of a corner of the film. Press the 2 pieces of tape firmly together, then quickly pull them apart to begin separating the clear liner away from the static side of the film.
Can I remove the film at a later stage?
Absolutely. Our blackout film is removable and reusable. You can just simply peel the film off the glass in seconds with no mess.
Why the film fall off after a while?
Please check if you have removed the liner, trimmed the edges or queegeed excess water and bubbles. Leave a 1/16” wide gap around the four perimeter edges of the film. This gap is essential for the proper thermal expansion of the glass.
VELIMAX 1/2-inch Frosted Reeded Glass Window Film is designed to give a beautiful appearance of modern appearance to your windows and doors, whether for privacy, to block out an unsightly view or for decorative purposes.
Besides prevent UV rays, it can also cut out a large proportion of the unwanted glare, whilst still allowing natural light to pass through. It will work on any smooth glass surface and can be used anywhere in the home, requires no additional cleaning and can be installed at a fraction of the cost.
Fancy and Stylish
Freshen up your windows and create a relaxing atmosphere to your home.
Privacy and Sunlight
Misshapes the view and limits while enabling a lot of light to go through.
Reduce Glare
Blocks UV rays by 99% and reduces the fading and aging of the furnishings.
Easy to Install
Measure Glass?Clean Glass?Cut Film?Remove Liner?Spray Water?Hang Film?Squeegee Film?Trim Edges
Suitable for all kinds of smooth and flat glass surfaces.
It's a smart choice to embellish your room by adding style and concealing an undesirable view seen through a window.
How to remove the air bubbles?
Use a plastic card to squeegee air bubbles and water. If it's hard to get rid of the bubbles, uncover the window film, spray more water between the glass and the film and squeegee firmly again. Water will make it much easier to remove bubbles.
Any tips to peel off the protective liner?
Attach 2 pieces of transparent tape to the front andback surfaces of a corner of the film. Press the 2 pieces of tape firmly together, then quickly pull them apart to begin separating the clear liner away from the static side of the film.
Can I remove the film at a later stage?
Absolutely. Our blackout film is removable and reusable. You can just simply peel the film off the glass in seconds with no mess.
Why the film fall off after a while?
Please check if you have removed the liner, trimmed the edges or queegeed excess water and bubbles. Leave a 1/16” wide gap around the four perimeter edges of the film. This gap is essential for the proper thermal expansion of the glass.