- Free 30-day Returns
Meet Your Seller
Bykski GPU Water Block for EVGA GeForce RTX 3090 TI FTW3 Ultra Gaming
- FITS THE LISTED CARDS: Made for the EVGA GeForce RTX 3090 TI FTW3 Ultra Gaming and EVGA GeForce RTX 3090 TI FTW3 Gaming only. Full-coverage block with backplate, matched to these circuit boards.
- FULL CONTACT COOLING: One block cools the GPU chip, the memory and the power stages in a single pass. The base is high purity copper with nickel plating under a clear acrylic top.
- ADDRESSABLE RGB LIGHTING: The block carries 5V addressable RGB lighting. It plugs into a 5V 3-pin ARGB header on the motherboard or an ARGB controller.
- QUIET, VISIBLE LOOP: A water block moves the card's heat to your radiators instead of its stock fans, so the card can run quieter. The acrylic top puts the flow through the block on show.
- USA SUPPORT, FRIENDLY AND EXPERIENCED: Tyler Direct provides knowledgeable US-based support for troubleshooting and compatibility questions. Every purchase carries a 1-year warranty covering defects.
Any questions? Ask CelesteSM will help you find out quickly.
The Bykski N-EV3090TIFTW3-X is a full-coverage GPU water block with a backplate for the EVGA GeForce RTX 3090 TI FTW3 Ultra Gaming and the EVGA GeForce RTX 3090 TI FTW3 Gaming. One nickel-plated copper block cools the GPU chip, the memory and the power stages directly, under a clear acrylic top with 5V addressable RGB lighting.
Why it works
- Direct cooling of the GPU chip, memory and power stages for lower temperatures and room for higher overclocks
- Running cooler can extend the card's life
- High-flow design runs in series or in parallel with other blocks
- 5V addressable RGB lighting
Compatibility
- EVGA NVIDIA 3090 - GEFORCE RTX 3090 Ti FTW3 ULTRA GAMING
- EVGA NVIDIA 3090 - GEFORCE RTX 3090 Ti FTW3 GAMING
Specifications
- Block Material: Nickel Electroplated High Purity Copper / PMMA (Acrylic)
- Backplate Material: Black Anodized Aluminum (not in contact with coolant)
- Dimensions: 288.78 x 132.3 x 6 mm
- Port Thread: G1/4
In the box
- GPU Water Cooling Block
- Installation Hardware, including thermal paste
- 5v Addressable RGB (RBW)
Installation
- Drain the loop if the PC is already water cooled, and remove the card from the PC.
- Remove the stock cooler from the card.
- Clean the old thermal compound from the GPU chip, memory and power stages.
- Prepare the contact surfaces with the included thermal paste and hardware.
- Set the block on the card, line it up and fasten it with the included screws.
- Mount the backplate on the back of the card.
- Install the card, connect the G1/4 ports to your loop in series or in parallel, and fill the loop.
- Connect the lighting lead.
Warnings
Never power the card without the loop installed and the pump running.
Thermal pads go where the block has raised contact points; the GPU chip takes thermal paste.
Tighten the block's screws evenly and finger tight; over-tightening can crack the acrylic top.
The lighting plugs into a 5V 3-pin addressable (ARGB) header or an ARGB controller only. A 12V 4-pin RGB header will damage it.
No printed instructions are included; the installation illustration is in the product images.
Self-installation by users experienced with PC water cooling. The manufacturer may update the design, so the product you receive may differ slightly from the images. The manufacturer is not liable for damage caused by misuse, improper installation, operation outside the stated specifications, or incompatible hardware or fluids. Installing and using this product means you accept these risks.
Warranty & Returns
Warranty, Returns, And Additional Information
Warranty
- Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
- CONTACT
Return Policies
- Return for refund within: 30 days
- Return for replacement within: 30 days
- This item is covered by Tyler Direct Return Policy
Manufacturer Contact Info
- For a directory of all our manufacturers, please click below.
- Manufacturers Directory














