Skip to main content
  • $14.99
  • Free 45-day Returns
  • Ships from China.
    Price alert
    Shop it at NeweggBusiness.

    SXDOOL SXD8038B24H 80mm 24V PWM Cooling Fan, 6000 RPM, Dual Ball Bearings, with Guard and Screws

    • 80 x 80 x 38 mm, 24 V DC, 0.50 A
    • 6000 RPM +/-10%, 57 dBA
    • 83.5 CFM airflow, 21.8 mmH2O static pressure
    • Dual ball bearings, XH-2.54 4-pin PWM + FG
    • Includes 80 mm guard and four 4 x 10 mm screws
    +
    +
    Overview
    Specs
    Reviews

    Any questions? Ask CelesteSM will help you find out quickly.

    SXDOOL SXD8038B24H 24V cooling fan front view
    High static pressure for restricted airflow paths
    SXD8038B24H | 24 V DC | 80 x 80 x 38 mm

    Filters and grilles can restrict airflow. Rated static pressure is 21.8 mmH2O. Rated airflow is 83.5 CFM. These are separate ratings. Installed airflow depends on system resistance.

    Angled view of the square fan housing and impeller
    Fan assembly

    The 80 mm square frame surrounds the impeller. Leave room on both sides for air to enter and exit.

    Ball bearing detail from the fan assembly
    Dual ball bearings

    Two ball bearings support the rotating shaft as the fan runs.

    Stator and control electronics of the fan
    Motor construction

    The stator and windings and control board are shown separately to reveal the parts inside the fan.

    Side view of the 38 mm deep fan housing
    Housing depth

    Allow 38 mm for the fan body plus clearance for the wire guard and cable and connector.

    Connect power and speed control
    XH-2.54 four-pin connector on the fan cable
    XH-2.54 4-pin connector
    Power wiring

    Black wire is DC negative. Red wire is +24 V DC. Rated current is 0.50 A. Match polarity before applying power.

    Control and feedback

    Blue wire is the PWM speed control input. Yellow wire is the FG tachometer output for speed monitoring. Use a compatible controller.

    Verify compatibility
    Electrical requirements
    • 24 V DC supply and compatible PWM/FG interface

    Match before connecting

    Check connector fit and orientation against the equipment documentation. A four-pin plug alone does not establish compatibility with a standard PC fan header.

    Check the replacement against your equipment
    Dimension lines indicate fan body width and height and depth
    Measure the frame

    The fan body measures 80 x 80 x 38 mm or 3.15 x 3.15 x 1.50 in. Compare mounting holes and available depth with the existing installation.

    Labeled face of the 24 V 0.50 A fan
    Check the operating ratings

    Verify that the equipment supplies 24 V DC at the rated 0.50 A. Rated speed is 6000 RPM +/-10%.

    Fan and 80 mm wire guard with four mounting screws
    Hardware supplied

    Each kit includes one fan and one 80 mm wire guard plus four 4 x 10 mm case screws.

    Does this fit a standard 12 V PC fan header?

    This fan requires 24 V DC. A four-pin plug alone does not establish compatibility. Check voltage and polarity and connector fit and the PWM/FG signals against the equipment documentation.

    What noise level should I plan for?

    The stated noise level is 57 dBA. Panel mounting and grilles and enclosure acoustics can change what you hear after installation.

    Can I replace an enclosure or power-supply fan?

    Compare frame size and hole spacing and depth and airflow direction. Match power and control wiring. Cooling requirements depend on the equipment and its airflow restrictions.

    The SXDOOL SXD8038B24H is a 24 V axial cooling fan for industrial enclosures, equipment chassis and compatible power supplies. Its 80 × 80 mm frame is 38 mm deep. Check depth clearance, mounting-hole spacing and airflow direction against the original fan before installation.

    Dual ball bearings support the rotor at a rated speed of 6000 RPM ±10%. The 83.5 CFM airflow and 21.8 mmH2O static pressure are separate specifications. Installed airflow depends on the resistance of the equipments air path. The fan is rated at 0.50 A and 57 dBA.

    The XH-2.54 4-pin connector provides separate leads for power, speed control and feedback. Black is DC negative, red is +24 V DC, yellow is the FG speed-feedback output and blue is the PWM speed-control input. Match the connector, wire functions and controller signal requirements to the equipment.

    The kit includes one SXD8038B24H fan, one 80 mm iron wire guard and one pack of four 4 × 10 mm case screws.

    Warranty & Returns

    Warranty, Returns, And Additional Information

    Warranty

    • Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
    • CONTACT

    Return Policies

    Manufacturer Contact Info

    LOADING...