Specifications: Video Channel: 1 channel bi-direction
Signal Mode: NTSC / PAL / SECAM
Video Connector: BNC
Video Bandwidth: 60 MHz
Video Input / Output Voltage: 1.0 Vpp / typical peak-to-peak value
Video Input / Output Impedance: 75 ohm / unbalanced interface
Supported Video Type:
1080p: AHD / TVI / CVI
480p: CVBS
Video Digital Bit Width: 8/10 bit
Differential Gain (DG): < 1.3% (typical value)
Differential Phase (DP): < 1.3 degree (typical value)
SNR Weighted: > 67 dB (typical value)
Data Channel: 1 channel
Physical Protocol: RS485
Operation Mode: Simplex
Data Connector: 3-pin terminal block with screw clamps
Data Rate: DC-115.2 Kbps
Bit Error Rate (BER): < 10ns
LED Indicators:
Power
Video
Link (fiber optic)
Power Requirement: 5V DC, 2A
Power Consumption: 4.8 watts (maximum)
Mechanical: Metal
Installation: Wall-mountable, DIN-rail (with optional...
Frequency Band: Frequency Band: 2.4 GHz, 5 GHz
Performance: Maximum data rate (2.4 GHz): 1148 Mbps ¦ Maximum data rate (5 GHz): 2400 Mbps
Capacity: Maximum number of clients 1024
Interface: 1 x 1000Base-T (PoE+) - RJ-45 ¦ 1 x 1Gb Ethernet/10Gb Ethernet - SFP+ ¦ 1 x 2.5 GBase-T (PoE+) - RJ-45
Part Number: 9U1-T750-US01
Standards: IEEE 802.1Q, IEEE 802.11b, IEEE 802.11a, IEEE 802.11g, IEEE 802.1x, IEEE 802.11i, IEEE 802.11n, IEEE 802.11k, IEEE 802.3at, IEEE 802.11ac, IEEE 802.11r, IEEE 802.11v, IEEE 802.3bt, IEEE 802.11ax, Wi-Fi Certified 6, EN 61000-4-2, EN 61000-4-3, EN 61000-4-5, RoHS, EN 60950-1, WEEE, EN 60601-1-2, IP67, EN 62311, EN 50121-4, IEC 61373, EN 50121-1, ISTA 2A
Specifications: PoE Standard: IEEE 802.3af (Power over Ethernet)
IEEE 802.3at (High Power over Ethernet)
PoE Power Supply Type: Mid-Span / Type B
PoE Power Output: 52V DC, 510 mA, Max. 26 watts
Power Pin Assignment: 4/5 (+), 7/8 (-)
Maximum Distance: 4 units, daisy-chain installation with 500m support
Data Rate: 10/100/1000 Mbps
Switch Architecture: Store-and-Forward
Maximum Frame Size: 1552 Bytes
Flow Control:
Back pressure for half-duplex
IEEE 802.3x pause frame for full-duplex
LED Indicators:
1 x PoE IN (Green)
1 x LAN Data (Green)
1 x PoE OUT (Green)
Power Requirements: IEEE 802.3at compliant with voltage within 52V-56V DC
Power Consumption: 3.2 watts (system maximum)
Specifications: Interface:
PoE (Power + Data) Input Port: 1 x RJ-45 STP
Data” Output Port: 1 x RJ-45 STP
DC Out Plug Connector: 1
LED Indicator System: PoE In x 1 (Green)
Network Cable:
10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
100Base-TX: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m (328 ft.)
EIA / TIA-568 100-ohm STP (100m)
Data Rate: 10/100/1000 Mbps (varies on Ethernet device attached)
DIP Switch: 12V DC / 24V DC output voltage
Power Input: 802.3at PoE+ 52 ~ 56V DC
PoE Standard: IEEE 802.3at High Power over Ethernet
Number of clients device can be powered: 1
Power Output:
12V DC, 2A max
24V DC, 1A max
Standards Compliance:
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3at...
Specifications: Multipurpose mounting bracket for indoor AP's supports mounting to hard wall, ceiling, pole or truss. Supports padlock security with ZoneFlex R710.
Kit Content:
1 x Sheet metal mounting bracket
2 x #6 wood screws & anchors
Specifications: Power consumption: 1.3 watts via POE
Forwarded PoE Power:
Up to 75 watts depending on standard
Maximum current 0.7 amps on data pairs
Maximum current 1.5 amps on spare pairs
PoE Standards:
IEEE 802.3af POE (15W) and IEEE 802.3at at POE Plus (2-event signature) (25-30W)
IEEE 802.3bt POE (to 75W)
Custom POE (incl. "always-on 48V" and "4-pair" POE)
Ethernet Interface:
Two independently auto-configuring 10/100 ports
(10Base-T / 100Base-TX, half / full duplex)
Patch or crossover cables supported
LEDs Status indicators:
Green LED - shows POE Power good
Yellow LED - shows Ethernet link / activity
Dimensions: 1.22" x 8.27" x 1.97"
Weight: 0.23 lb.
Mounting: 2/4 Bolt 7mm mounting holes. On 50/60mm centres
Operating temperature: -40 degree C to 70 degree C [-40 degree F to 158 degree F]
Relative humidity: Up to 85%, non-condensi...
Antenna: Integrated down tilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 5.3 dBi in 2.4 GHz, 6.0 dBi in 5 GHz (5.8 dBi in dual-5 GHz mode) and 6.0 dBi in 6 GHz (5.9 dBi in dual-6 GHz mode). Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The down tilt angle for maximum gain is roughly 30 to 40 degrees.