- Free 30-day Returns
Meet Your Seller
Solarity ArrRGB DAC Rev. 4.1 - Digital RGB to Analog RGB Converter (SYT-0003)
- Solarity Technology presents the "ArrRGB DAC"! The ArrRGB DAC Rev. 4.1 is a 4 channel RGB device that allows you to use a Digital/Addressable signal from a motherboard header or RGB controller and control Analog RGB devices on 4 different channels vi
- Instructions:
- Power off Computer!
- Fasten the ArrRGB DAC to a removable 2.5 or 3.5 hard drive caddy. Please use M3 screws, which is the standard screw size used to attach hard drives.
- Connect a Corsair controller or Motherboard header to the input. The board can only take one input. These cables can come with 3rd party devices or can be purchased separately.
- Plug in a standard floppy drive power connector. Most PSUs come with one; Molex or SATA adapters can be purchased separately.
Any questions? Ask CelesteSM will help you find out quickly.
The Solarity Technology ArrRGB DAC Rev. 4.1 is a digital to analog RGB converter: it takes the addressable (digital) RGB signal from a motherboard header or an RGB controller and uses it to drive analog RGB devices on 4 separate channels. A jumper selects 12 V or 5 V for the analog outputs.
Properties
- Type: Digital (addressable) RGB to analog RGB converter
- Analog channels: 4
- Input: 1 addressable RGB input (Corsair controller or motherboard header)
- Outputs for daisy-chaining: Corsair Out and MB Out
- Analog output voltage: 12 V or 5 V, set by jumper
- Power: Floppy drive power connector
One controller for analog RGB too
The ArrRGB DAC needs an addressable signal to work; it does not run without a controller or motherboard header. Each of its four analog channels is addressed as a single LED in your RGB software, so every analog device you connect can have its own color and effect.
Daisy-chain more devices
From the digital output you can chain more ArrRGB DACs or other addressable RGB devices. Unlike the input, the Corsair Out and MB Out outputs can be used at the same time. Keep the LED limits below in mind.
Installation
- Power off the computer.
- Fasten the ArrRGB DAC to a removable 2.5" or 3.5" drive caddy with M3 screws, the standard hard drive screw size.
- Connect a Corsair controller or a motherboard header to the input. The board takes only one input. Cables come with many third party devices or can be bought separately.
- Plug in a standard floppy drive power connector. Most power supplies have one; Molex or SATA adapters are available separately.
- Connect up to four analog RGB devices to the four headers. Splitters may be used, as long as you stay within the LED limits.
- Configure your controller.
Compatible controllers
- Corsair Commander Pro
- Corsair Lighting Node Pro. In many cases a Corsair RGB strip is needed between the DAC and the controller, most likely because of timing settings in the Lighting Node Pro firmware.
- Motherboard addressable RGB headers with a matching connector: ASUS, ASRock, MSI and newer Gigabyte boards
- Many other addressable RGB controllers with a matching connector that drive 5 V WS2812B addressable LEDs. Solarity cannot test every device, but says most should work.
Two power modes
- 12 V mode: supplies 12 V to the analog devices on the standard connector. Do not exceed 150x 12 V LEDs powered by each board, and 50x 5 V addressable LEDs powered by each board.
- 5 V mode: supplies 5 V to the analog devices on a non-standard RGB connector. Do not exceed 50x LEDs powered by each board.
Technical data
- Model: SYT-0003
- Product: ArrRGB DAC Rev. 4.1, RGB digital to analog converter
- Analog channels: 4
- Analog output voltage: 12 V or 5 V (jumper "Analog Out Voltage")
- LED limits per board: 150x 12 V LEDs, 50x 5 V LEDs
- Power input: Floppy drive power connector
- Mounting: M3 screws on a 2.5" or 3.5" drive caddy
- Color: Black PCB
Notes
- Only attach devices while the ArrRGB DAC is powered off. This reduces the chance of reversing the polarity, which may damage your devices.
- Check the jumper before you power up: there are two power modes, and the wrong one can damage your analog devices.
In the box
- 1x Solarity ArrRGB DAC Rev. 4.1 converter board
Warranty & Returns
Warranty, Returns, And Additional Information
Warranty
- Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
- CONTACT
Return Policies
- Return for refund within: 30 days
- Return for replacement within: 30 days
- This item is covered by ModMyMods Return Policy
Manufacturer Contact Info
- For a directory of all our manufacturers, please click below.
- Manufacturers Directory











