for Corsair 90° Angled 12VHPWR Cable Dual 8 Pin to 16 Pin 12V-2x6 600W PCIe 5.0 GPU Power Cord, 16AWG 60cm, for Type 3/Type 4 PSUs, RTX 5090/5080/4090/4080 Ready (Type A(4-Pin on Bottom))

1. CORSAIR TYPE A CONFIGURATION 4-PIN ON BOTTOM DESIGN This cable features the official Corsair Type A configuration, with the 4-pin sense wires positioned on the bottom side of the connector (closer to the GPU PCB) . This design is specifically optimized for graphics cards with thick backplates or limited clearance above the power connector, ensuring full insertion without interference. Available in two versionsType A (4-Pin on Bottom) and Type B (4-Pin on Top)giving you the freedom to route the cable above or below your graphics card for the perfect fit in your build .
2. 90° ANGLED CONNECTOR PREVENTS SHARP BENDS The factory-molded 90° angled 12V-2x6 connector eliminates the need to bend cables near the GPU portthe #1 cause of connector failure . Standard straight cables often require sharp bends that press against glass side panels; our angled design routes the cable cleanly downward, reducing stress on both the GPU port and your case. It is recommended to maintain at least 35mm of straight cable before any bend .
3. 600W POWER DELIVERY RTX 50 & 40 SERIES READY Built to power the most demanding graphics cards. This cable delivers up to 600W of stable power through two PCIe 8-pin inputs on your Corsair PSU. Fully compatible with NVIDIA GeForce RTX 50 Series (5090/5080/5070 Ti) and RTX 40 Series (4090/4080/4070 Ti) . Supports both 12VHPWR and the updated 12V-2x6 GPU connector standardsthe cable works with both, as the difference lies in the GPU-side socket, not the cable itself .
4. PREMIUM 16AWG CONSTRUCTION HIGH THERMAL ENDURANCE Built with high-quality 16AWG tinned copper wire, capable of carrying up to 55A of current with 105°C temperature resistance . Delivers stable power with minimal voltage drop. The plug terminals feature alloy copper with tin plating for superior conductivity and corrosion resistance. Each cable is factory-tested for reliability under load.
5. EXACT FIT FOR CORSAIR TYPE 3 / TYPE 4 MODULAR PSUs Engineered specifically for Corsair Type 3 and Type 4 power supplies. Compatible with RM, RMx, RMi, RMe, HX, HXi, AX, AXi, SF, TX-M, CX-M series. NOT compatible with other PSU brands (EVGA, Seasonic, Lian Li, etc.) or Corsair AX Gold/HX Bronze seriesusing with incompatible PSUs may cause permanent damage .
6. OPTIMAL CABLE LENGTH 650MM (25.6 INCHES) Total length of 650mm (25.6 inches) provides ample reach for routing behind the motherboard tray or through cable management channels. Includes a reusable cable tie for clean organization.
7. CRITICAL INSTALLATION SAFETY WARNINGS The #1 cause of 12VHPWR/12V-2x6 connector failure is incomplete insertion and bending within 35mm of the connector . When connecting to your GPU: Push the connector straight and firmly into the GPU port until you hear a CLICK Verify that no gap exists between the connector housing and GPU socket Do not bend the cable within 35mm (1.4 inches) of the connectormaintain a straight approach as required by PCI-SIG specifications Regularly inspect the connector for signs of melting or discoloration, especially with high-power GPUs like RTX 5090.

When building a high-end PC with a powerful graphics card like the NVIDIA GeForce RTX 5090 or RTX 4090, cable management becomes criticalespecially in compact cases where the side panel presses against the stiff power cable. The Corsair Type A 90° Angled 12V-2x6 Cable solves this problem with a factory-molded 90° connector that routes cleanly without sharp bends .

This cable features the official Corsair Type A design, with the 4-pin sense wires positioned on the bottom side of the connector (closer to the GPU PCB) . Corsair offers this cable in two versionsType A (4-Pin on Bottom) and Type B (4-Pin on Top)allowing you to choose the orientation that best fits your graphics card's power connector layout .

Type A is ideal for:

1. Graphics cards with thick backplates that may interfere with connectors
2. GPUs where the area above the power connector has limited clearance
3. Ensuring full insertion without obstruction from backplate or cooling components

Standard straight 12VHPWR cables often require bending immediately after the connector, which can:

1. Create stress on the GPU power port
2. Push against glass side panels
3. Increase the risk of incomplete insertionthe #1 cause of connector melting

Our 90° angled design eliminates these issues by directing the cable where you need it to godownward toward the PSU shroud or backward toward the cable management channel.

RTX 50 SERIES CONFIRMED COMPATIBLE

This cable is fully compatible with NVIDIA GeForce RTX 50 Series (5090, 5080, 5070 Ti, 5070) and RTX 40 Series GPUs . Both 12VHPWR and 12V-2x6 standards use identical cablesthe difference is only in the GPU-side connector socket, which is fully backward compatible .

Important RTX 50 Series Note: The CORSAIR Power Bridge is not compatible with RTX 50 Series Founders Edition GPUs due to thei