Your Browsing History
- Free 30-day Returns
$73.99
Meet Your Seller
GOOZEEZOO MMDVM Duplex Hotspot Module Dual Hat with 0.96 OLED Display V1.47 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi (with OLED)
- if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat ; HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece.
- WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4.
- WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion
- FREQUENCY: UHF 433-900MHz, VHF 144-220 MHz. NOTE: TX =0, RX=0. Modem select: STM32_HS_GPIO ; To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to 1. This leaves the screen on all the time. Otherwise, it goes blank when idle
- EASY OPERATION: The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx,Rx,PTT,Mode)
+
+
Overview
Specs
Reviews
Any questions? Our AI beta will help you find out quickly.
Try me now
DESCRIPTION
Original cystal: Original ECS-TXO-3225- 147.4 -TR from USA
Duplex variant of MMDVM_HS_HatThis PCB uses the MMDVM_HS. It has two ADF7021 onboard and allows for duplex operation with two time slots on DMR.
Setting Tips: Modem
select:
STM32_HS_GPIOFREQUENCY: UHF 433-900MHz, VHF 144-220 MHz.
NOTE: TX =0, RX=0.
Modem select: STM32_HS_GPIO; To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set
Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to
1. This leaves the screen on all the time. Otherwise, it goes blank when idlePackage
List: 1x MMDVM duplex HotSPOT Module2x Antenna2x SMA socket
Original cystal: Original ECS-TXO-3225- 147.4 -TR from USA
Duplex variant of MMDVM_HS_HatThis PCB uses the MMDVM_HS. It has two ADF7021 onboard and allows for duplex operation with two time slots on DMR.
Setting Tips: Modem
select:
STM32_HS_GPIOFREQUENCY: UHF 433-900MHz, VHF 144-220 MHz.
NOTE: TX =0, RX=0.
Modem select: STM32_HS_GPIO; To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set
Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to
1. This leaves the screen on all the time. Otherwise, it goes blank when idlePackage
List: 1x MMDVM duplex HotSPOT Module2x Antenna2x SMA socket
Warranty & Returns
Warranty, Returns, And Additional Information
Warranty
- Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
- CONTACT
Return Policies
- Return for refund within: 30 days
- Return for replacement within: 30 days
- This item is covered by mafengkeji Return Policy
Manufacturer Contact Info
- For a directory of all our manufacturers, please click below.
- Manufacturers Directory
LOADING...