Question 1

this should work for an old P-III with Millennium as an  O.S. to get on the internet??

Accepted Answer

I checked online and I think that all of the Pentium III motherboards have ISA slots.  If that is correct then this card will not fit and since it doesn't have a Millennium driver I would have to say that it will not work.

Question 2

Is this card not compatible with Windows 7? I installed it in my mother-in-law's computer and when I booted it up it installed drivers right away. Problem is that now when I go to certain websites it simply times out. None of the other pc's on this network have any problem like this. probably user error but just want to make sure.

Accepted Answer

It should be compatible with Windows 7.  Sounds like the wrong driver installed itself.  I would uninstall/reinstall the correct driver:
1. Open device manager
2. Select Network Adapter
3. Open this adapter
4. Under Driver tab select uninstall
5. Turn off computer
6. Remove card
7. Power on computer & install driver
8. Turn off computer
9. Reinstall card & restart computer
Proper driver should install for the card, then retest on internet.
If problem still persists contact TP-Link Tech Support for suggestions.  Good luck & hope this helps!

Question 3

It says it is a 32 bit card and my motherboard is 64 will it work with a 64 bit MB?

Accepted Answer

It works for my 64 mobo. I think you can always use 32 in a 64 but it will only run at 32. I had to buy this b/c the built-in one on my board stopped working, and it was affordable. I hope this was helpful. Happy shopping!

Question 4

Can i use this card to to emit a wifi signal from the PC?

Accepted Answer

No.  This is just for wired connectivity.

Question 5

will this work with windows 10?

Accepted Answer

Yes, I'm using Windows 10 and it works great for me.

Question 6

Does this come with a "half-height" bracket??  It looks like the card would fit, just need to convert to 1/2 height.

Accepted Answer

No. Among all the network cards I've purchased none of them had an extra half-height bracket. Usually they're riveted to the PCB You'll have to perform your own modification, and ascertain PCB height for fit. Fully seated, my PCB extended 1.64" above the socket surface.

Question 7

My card slot only has room for two of the 3 tabs at the bottom of the card(the larger one and the one at the back of the card. Do I need to be able use all 3 tabs? Or will all three tabs fit into my 2 slots?

Accepted Answer

Typically, if it fits, it will work. I installed this card into my untangle server, 2 of 3 tabs fit, and I was getting full gigabit speeds. I have since upgraded to a motherboard with dual ether net ports, but I keep the card just in case.

Question 8

What is the empty socket for that is seen in the board?

Accepted Answer

That empty slot is nothing you need to worry about. Back in the dawn of computers, components were general purpose and special chips were programmed to the specific task needed. They would be installed in slots like that one. The PCI format has been around for a while, and network cards really haven't had to be ungraded at all, beyond adding the gigabit standard. So it's not uncommon to see a tried and reliable development board being used. Sorry for the history lesson, but it's the only way I could think of to explain that slot. All the best!

Question 9

yes i have an emachines t5010 tower and was wondering is it work on my tower I am trying to get it up and running it is running windows xp?

Accepted Answer

This Network Adapter comes with Windows XP drivers, but I do not know if your eMachine T5010 has a PCI slot inside. I do know that your eMachine T5010 already has a 10/100 Ethernet port built in. So I am not sure why you need this network adapter unless you need the Gigabit speed.

Question 10

Does this devices support Message Signaled Interrupts (MSI)?  To tell, on Linux run 'sudo lspci -v', locate the device and look for either an MSI or MSI-X capability.  On Windows, run device manager, select the device and look at resources and scroll to see whether the IRQ is listed as a negative number.  The Realtek product spec for the 8169SC says that it should, but it also says that for the 8110SC, which does not in the instance I received (different product).  Thank you for checking!

Accepted Answer

No sure if you were answering no to my question or other one above.  No, it won't work in Win server 2003?  If not, is it because there is no driver supplied or is it known to not work in Win server 2003?

Brand	TP-Link
Model	TG-3269

Standards	IEEE 802.3, 802.3u, 802.3ab, 802.3x, 802.1q, 802.1p
Speed	10/100/1000Mbps
Connectors	1 x RJ45
Interface	PCI
BUS	32-bit PCI
LEDs	1000Mbps Link/Act, 100Mbps Link/Act, 10Mbps Link/Act, Duplex
Temperature	0°C ~ 40°C
Humidity	10 % ~ 90 % (Non-condensing)

TP-Link TG-3269 Gigabit Network Adapter 10/100/1000Mbps PCI 1 x RJ45

TP-Link TG-3269

Learn more about the TP-Link TG-3269

Customer Reviews of the TP-Link TG-3269

Warranty & Returns

Warranty, Returns, And Additional Information

Warranty

Return Policies

Manufacturer Contact Info

Item#: N82E16833704011