Question 1

The case fans do not have any LED's, correct?

Accepted Answer

It doesn't have any LED fans, but there are 7 available places that you can add those if you like. This is a very nice case!

Question 2

what the defference between this case and the antec 1100 super mid tower case?

Accepted Answer

The information about the Antec 1100 V2 has been removed from the site.

I am in a now 3 and half week process of RMA Issues with Antec without resolution as a result of the 4 Pin Molex/ 3 Pin Fan Hub not installed. This is a REQUIRED PART based on ANTEC's design.

When Antec had a site page dedicated to the ANTEC 1100 V2, picture 9 clearly showed this $3 Part and based on out of box shipped product, you have three 3 Pin Fans with no means to nicely plug into a PCB HUB even though there are internal screw placement for the part. This is the only difference from V1 to V2, and the design is more in line with a water cooling setup.

I have had my case for a month and unable to install my components due to a tremendous amount of mis-communication by ANTEC. While yet again another solution is pending, I am truly not a happy purchaser of the case, but need this case which is a double edge sword.

If you purchase this case, make sure you have one of the bays as UNUSED as you will require a FAN Controller at an additional cost due to a missing $3 Dollar part. You will want to be very picky on the fan controller as well and the good ones tend to be $35 or higher so include this with the overall purchase of this case if you intend to AIR COOL your system.

The installed fans are very low end/low CFM Fans, so include the cost of better fans when you consider this case as a purchase. You may think you are getting a great deal, but back end costs eliminate that savings, TRUST ME.

I still stand firm on my review, but I am posting this information in hope that I can prevent future customers from finding out these things later and faced with a ton of additional issues and potential significant loss of funds with RMA situations/required needs/return shipping loss/not being able to use other parts ordered because you can not afford a similar sized case from a new provider like I am facing. I am very disappointed in myself for not waiting for others to review this product b4 buying

Question 3

Will this case fit a Corsair H100i water cooler in the top?

Accepted Answer

I bought this case to house a gigabyte amd board with a single water cooler.  I couldn't say exactly what will fit where because i don't know what your stuff looks like, but there's a lot of room for a single or double in the top,  hope that helps.

Question 4

i would ike to know what the hard drive size is and what is the processor speed?

Accepted Answer

Not sure if this question was directed at the Antec Eleven Hundred V2 Black Computer Case, but the case holds 6 HDD and can run pretty much any motherboard/processor combo you put in it so speed is all up to the builder. Hope this helps!

Question 5

I have a Cooler Master v8 CPU cooler, would I still be able to install side panel fans?

Accepted Answer

I happen to use the same cooler and it fits no problem, however, you will not be able to install any fans on the side panel.

Question 6

what's the RPM on included fans?

Accepted Answer

I did know this but I forgot.  I called Antec and asked about the specifications on the fans when I purchased this case because I wanted to get more fans.   I know this is not the answer but hopefully it'll point you in the right direction.  Look up their site.  I tried to post their support number and website address and this answer form wont let me do it.

Question 7

Does it fit corsair H110i  water cooling ?

Accepted Answer

Honestly, I have not tried I, but it certainly is a big enough case.  I have six variable speed large antec fans in it and they seldom go above minimum speed, but I don't push the processor, either.

Question 8

The Antec web site states this model supports the XL-ATX  board size. Newegg states it handles E-ATX board size. Does the case support BOTH sizes???

Accepted Answer

Yes it will fit E-ATX and XL-ATX.

Question 9

Why would they remove the fan controller which was placed rear top?

Accepted Answer

Antec changed the design and went with two 120mm PWM fans instead of one 200mm single fan.

Questions & Answers