Q: I have a Toshiba Satellite S55t-A5161 that doesn't run "hot hot" but it ramps up its fan quite often, only running Skype and such. I have already taken it apart once to upgrade from an HDD to an SDD (<3 SSD) I run it constantly (Sometimes up to 10 days), I have it sitting on a cooling pad that have two small fans pushing air into the laptop, I'd just like to know if I can safely remove my stock paste, and replace with with this paste? With no issues. (I assumed it was simple, then got into different metals, etc)

I did this on an HP Envy with an I7 core and the cpu temp dropped 12 degrees Fahrenheit across the range. I do not have any bench mark software, but any freeware utility that does a registry scan will load the cpu.

Q: What is the maximum operating temprature of ARCTIC MX -4? Thanks John

I wired (on my first attempt) my water block wrong. I shot the cpu temp to 170F before the mobo shut it down not once, not twice, but 3 times. This is very durable thermal paste. The woman i made it for has had it for 7 months now and she's still reading temps of 90F across all 4 cores. It's also non conductive to electricity so if a little runs over it's not a dire emergency such as Artic Silver would be, since that's electrically conductive. The lower the temp the better obviously.

Q: Is this the best for an all aluminum HSF ? Is there a compound that is better for aluminum ?

i haven't tried too many different thermal compounds but this one is pretty good I use it with a fx6300 on a hyper 212 evo and get around 20c doing basic tasks around 50 under load.

Q: Would I be able to use this under the IHS on a core i7 7700K or is it too hot for this paste?

So you are delidding it? MX-4 should be fine, but if you are going to the trouble for that try the Thermal Grizzly Conductonaut. I haven't done this but it looks like the preferred one to use. Either way, looks like you should make sure you get 100% coverage on the die.

Q: what is the difference between the standard and the 2019 Edition of the MX-4?

Maybe a reformulation or it is anniversary packaging. In any case it is still an excellent paste.

Question 1

Is this tube enough for both a cpu and a gpu?

Accepted Answer

We used this for two CPUs so I would say "yes" because there was still some left over.  The servers this was used in have worked well.

Question 2

How would I apply this thermal compound on my AMD Athlon X4 860K with my Cooler Master Seidon 120V?

Thank you

Accepted Answer

Use very little, no more than a grain of rice. Seriously. A little goes a long way when the heatsink/waterblock presses against the CPU/GPU.

Personally, I like to pre-spread the compound to prevent any air bubbles, which would turn into hot spots on the CPU/GPU, degrading performance.

Watch the videos for examples.

Question 3

Is this tube enough for both a cpu and a gpu or will I need a bigger tube?

Accepted Answer

ya it would be ok, i have socket'd 4 cpu's  and still have well over half, and about to use it on a gpu very soon.

Question 4

Does this have a curing time like Arctic Silver 5 does?

Accepted Answer

No, it has no curing time. The curing time on AS5 can also be heavily reduced or even eliminated by reading the manual that comes with it and applying the Tinting method.

Question 5

Does this also work with GPUs?

Accepted Answer

Yes, just be sure the heatsink or waterblock you are using is made for direct contact to the GPU vs a thermal pad.  I used this MX-4 on my two GTX-780s with Watercool heatkiller waterblocks and it works great.  The heatkiller uses direct contact on the GPU and thermal pads for the memory and VRMs.  Both cards are overclocked in SLI and do not go over 37C.

Question 6

I have a Toshiba Satellite S55t-A5161 that doesn't run "hot hot" but it ramps up its fan quite often, only running Skype and such. I have already taken it apart once to upgrade from an HDD to an SDD (<3 SSD) I run it constantly (Sometimes up to 10 days), I have it sitting on a cooling pad that have two small fans pushing air into the laptop, I'd just like to know if I can safely remove my stock paste, and replace with with this paste? With no issues. (I assumed it was simple, then got into different metals, etc)

Accepted Answer

I did this on an HP Envy with an I7 core and the cpu temp dropped 12 degrees Fahrenheit across the range. I do not have any bench mark software, but any freeware utility that does a registry scan will load the cpu.

Question 7

What is the maximum operating temprature of ARCTIC MX -4?

Thanks 
John

Accepted Answer

I wired (on my first attempt) my water block wrong. I shot the cpu temp to 170F before the mobo shut it down not once, not twice, but 3 times. This is very durable thermal paste. The woman i made it for has had it for 7 months now and she's still reading temps of 90F across all 4 cores. It's also non conductive to electricity so if a little runs over it's not a dire emergency such as Artic Silver would be, since that's electrically conductive. The lower the temp the better obviously.

Question 8

Is this the best for an all aluminum HSF ? Is there a compound that is better for aluminum ?

Accepted Answer

i haven't tried too many different thermal compounds but this one is pretty good I use it with a fx6300 on a hyper 212 evo and get around 20c doing basic tasks around 50 under load.

Question 9

Would I be able to use this under the IHS on a core i7 7700K or is it too hot for this paste?

Accepted Answer

So you are delidding it? MX-4 should be fine, but if you are going to the trouble for that try the Thermal Grizzly Conductonaut. I haven't done this but it looks like the preferred one to use. Either way, looks like you should make sure you get 100% coverage on the die.

Question 10

what is the difference between the standard and the 2019 Edition of the MX-4?

Accepted Answer

Maybe a reformulation or it is anniversary packaging. In any case it is still an excellent paste.

Brand	ARCTIC COOLING
Series	Arctic Cooling MX-4
Model	AC-MX4

ARCTIC MX-4 Thermal Paste, Carbon Based High Performance Thermal Compound for All Coolers, Thermal Interface Material, 4 Grams

Learn more about the ARCTIC COOLING AC-MX4

Customer Reviews of the ARCTIC COOLING AC-MX4

Warranty & Returns

Warranty, Returns, And Additional Information

Warranty

Return Policies

Manufacturer Contact Info

Item#: N82E16835186038