3 in 1 Solder Wick Braid with Flux, Desoldering Wick No Clean Less Dross Soldering Wick(0.08/0.1/0.12in, 10ft Each)
Soldering Wick Coated Braid for Electronics Component Repair, PCB Circuit Boards (0.08/0.1/0.12in, 10ft Each)
- 1. The Solder Wick Braid made of precise geometric shapes woven from pure copper.
- 2. Braided Solder Wick Greatly reduces damage to the circuit board and has good thermal conductivity and tin plating performance.
- 3. Solder Wick Braid effect of pure copper material is significant, and a small amount of suction tape is used to remove more solder.
- 4. Computer motherboard: Place the soldering iron on the solder wick then slowly move it on the chip pad. When the solder melts, it will be sucked up by the Solder Wick Braid, sucking up all the solder between the pins. This way, the motherboard can be cleaned very cleanly. Afterwards, thoroughly clean the area with a cleaning agent.
- 5. Mobile phone motherboard: When removing solder, it absorbs excess solder, is resistant to oxidation and corrosion, has good thermal conductivity and tin plating performance, and absorbs solder cleanly. During disassembly and soldering, after removing the chip, there will still be a large amount of solder on the circuit board, which will affect the soldering of the chip. Usually, a Solder Wick tape is used to clean it up.
3 in 1 Solder Wick Braid with Flux
3 in 1 Solder Wick Braid with Flux
Specification :
Item name : Braided Solder Wick
Material: Pure copper (wire and strip weaving process)
wires Size:0.08/0.1/0.12in, 10ft(25*30mm/30*30mm/35*30mm, length : 3Meter)
Tape size: 46*12mm
Advanatages: Smooth tin suction,Can resist oxidation ,Ultra low residue,Resistance to corrosion, good thermal conductivity,NO Clean .
Widely Used: Braided solder wicks are suitable fora variety of Electronics Component Repair, PCB Circuit Boards ,computer and phone mother board repair, edge connectors, wire pack pins and any other terminals.
Package include : 3pcs/box
Usage steps: 1. For the solder that needs to be removed, place an appropriate length of Braided Solder Wick on the cleaned solder point, and then gently press and heat the solder with an electric soldering iron nozzle to melt it before being sucked by the Solder Wick. 2. Once the solder is absorbed, please remove both the soldering iron and the Braided solder wick at the same time 3. Cut off the used solder wick with pliers.
suitable fora variety of Electronics Component Repair, PCB Circuit Boards ,computer and phone mother board repair, edge connectors
3 in 1 Solder Wick Braid with Flux, Desoldering Wick No Clean Less Dross Soldering Wick(0.08/0.1/0.12in, 10ft Each)
Soldering Wick Coated Braid for Electronics Component Repair, PCB Circuit Boards (0.08/0.1/0.12in, 10ft Each)
- 1. The Solder Wick Braid made of precise geometric shapes woven from pure copper.
- 2. Braided Solder Wick Greatly reduces damage to the circuit board and has good thermal conductivity and tin plating performance.
- 3. Solder Wick Braid effect of pure copper material is significant, and a small amount of suction tape is used to remove more solder.
- 4. Computer motherboard: Place the soldering iron on the solder wick then slowly move it on the chip pad. When the solder melts, it will be sucked up by the Solder Wick Braid, sucking up all the solder between the pins. This way, the motherboard can be cleaned very cleanly. Afterwards, thoroughly clean the area with a cleaning agent.
- 5. Mobile phone motherboard: When removing solder, it absorbs excess solder, is resistant to oxidation and corrosion, has good thermal conductivity and tin plating performance, and absorbs solder cleanly. During disassembly and soldering, after removing the chip, there will still be a large amount of solder on the circuit board, which will affect the soldering of the chip. Usually, a Solder Wick tape is used to clean it up.
3 in 1 Solder Wick Braid with Flux
3 in 1 Solder Wick Braid with Flux
Specification :
Item name : Braided Solder Wick
Material: Pure copper (wire and strip weaving process)
wires Size:0.08/0.1/0.12in, 10ft(25*30mm/30*30mm/35*30mm, length : 3Meter)
Tape size: 46*12mm
Advanatages: Smooth tin suction,Can resist oxidation ,Ultra low residue,Resistance to corrosion, good thermal conductivity,NO Clean .
Widely Used: Braided solder wicks are suitable fora variety of Electronics Component Repair, PCB Circuit Boards ,computer and phone mother board repair, edge connectors, wire pack pins and any other terminals.
Package include : 3pcs/box
Usage steps: 1. For the solder that needs to be removed, place an appropriate length of Braided Solder Wick on the cleaned solder point, and then gently press and heat the solder with an electric soldering iron nozzle to melt it before being sucked by the Solder Wick. 2. Once the solder is absorbed, please remove both the soldering iron and the Braided solder wick at the same time 3. Cut off the used solder wick with pliers.
suitable fora variety of Electronics Component Repair, PCB Circuit Boards ,computer and phone mother board repair, edge connectors