EMP Shield DC-12V-W Lightning Protection for Vehicles 12V

Why Do I Need An EMP Shield?
Our Most Common Question is: If the Grid is Down and I Have No Electricity, Why Do I Need an EMP Shield? 1. You will save thousands of dollars and potentially years of time. Electrical surges will destroy electrical equipment if not protected. In most cases, EMP Shield is cheaper than most home deductables. 2. Power may go out for a day or a year. However, when the power is restored, your home electrical system and electronics will still be operational. You will be able to assume your previous lifestyle. 3. If you have a backup power system, you will still be able to use your electrical system and electronics normally. Common backup power systems can include generators, solar power systems, and wind turbine systems. 4. Reduce your chances of fire. As seen in the Carrington event in 1859, many people were injured from electrical surge and fires produced from this CME (coronal mass ejection). The EMP Shield removes this excess electricity from your home and reduces your risk of fire. 5. EMP Shield can also protect your backup power systems.

6. EMP Shield protects against more than just EMP (Electromagnetic Pulse). Our technology also protects against CME (Coronal Mass Ejection / Solar Flares), Lightning, and Power Surges. We offer the worlds most robust, durable and proven EMP Protection systems. 2x locations in 2018 were struck with lighting with the EMP Shield Installed. Each home had ZERO damage and witnessed ZERO fire. 7. We offer 40 types of EMP Shield that can be used for homes, vehicles, backup power systems, industrial facilities, and DOD/DHS applications. If you need to protect an electrical system, EMP Shield has or will develop a device for you. 8. The EMP Shield Home Models can assist in preventing smart meter fires. Military Testing EMP Shield is the Worlds First Whole Home and Vehicle EMP Defense Technology to Surpass All Military EMP Testing Standards: MIL-STD-188-125-1 MIL-STD-464C MIL-STD-461G CS115, CS116, CS117 EMP Shield has been rigorously tested at the Keystone compliance facility which is a federally approved facility that is used to conduct many of today's most advanced and rigorous technological tests. Out testing and evaluations conducted at the facility have been documented in depth to show the true ability and durability of the EMP Shield. The testing results derived from Keystone compliance testing facility highlights EMP Shields true strength and capability. Below you will find the complete Keystone Compliance testing results of the EMP Shield. EMP Shield is a family of incredibly robust EMP, solar flare, and lightning defense technologies. They have been designed to exceed the US Military requirements for protection against a high-altitude nuclear detonation that results in an electromagnetic pulse. This family of products has been tested at Keystone Compliance, a DOD Certified Testing Laboratory, to verify compliance with the following
Military Standards: MIL-STD-188-125-1 High Altitude EMP; MIL-STD-461G Control of Electromagnetic Interference; MIL-STD-461-CS-115 The purpose of CS115 is to test an electronic or electrical system to withstand signals coupled onto the test units associated cabling. The test unit will be subjected to rise and fall times, pulse width, and amplitude as specified on Figure CS115-1 at a 30 Hz rate for one minute; MIL-STD-461-CS116 applies to 10 kHz to 100 MHz for all interconnecting cables, including power cables, and individual high side power leads; MIL-STD-461 CS117 apples to all safety-critical equipment interconnecting cables and non-safety critical equipment with interconnecting cables/electrical interfaces that are part of or connected to equipment performing safety critical functions. The goal is to ensure an test units ability to withstand lightning transients coupled onto the test units associated cables and power leads; MIL-STD-461-RS105 Transient electromagnetic pulse of up to 50 kV/m, double exponential wave with a rise time in the nanosecond range, that is applied to the equipment under test (EUT) at least 5 times and; MIL-STD-464C Electromagnetic Environmental Effects Requirements for Systems. Test results show that we begin shunting the overvoltage condition in less than 1 nanosecond, and our units are designed to shunt over 100, 000 Amps per phase.

Our devices are scalable to any size.
Summary of capabilities:
Features: Quick acting HEMP surge protection that switches in less than