- Free 30-day Returns
Meet Your Seller
Analog Devices EVAL-AD5941ELCZ AD5941 Electrochemical Evaluation Board, Electrochemical Measurement and Impedance Analysis Development Kit
- Official ADI Electrochemistry Evaluation Kit (EVAL-AD5941ELCZ) designed to configure the AD5941 high-precision impedance & electrochemical front end for measurements on a typical electrochemical cell, with BNC electrode interface, on-board calibration resistor and a custom micro-USB to alligator-clip cable for quick cell hookup.
- Full EIS Capability: 0.015 Hz to 200 kHz on-board waveform generator and high-speed DAC produce sine excitation across the frequency range used in real electrochemical impedance spectroscopy; a hardware DFT engine outputs real/imaginary parts directly, so no host-side FFT is required.
- Voltage, Current & Impedance Measurement in One Front End dual precision excitation loops (low-bandwidth and high-bandwidth), high-resolution ADC and a programmable switch matrix support potentiostat, amperometric, voltammetric and impedance measurements from a single board [verify ADC resolution datasheet lists 16-bit, 800 kSPS / 1.6 MSPS options].
- Flexible Electrode Wiring BNC electrode connector plus calibration resistor on board support both 2-wire and 4-wire cell connections; 4-wire mode removes lead and contact resistance error on low-impedance cells such as batteries.
- Rapid Bring-Up on Standard Tools Arduino Uno form-factor interface (works with the EVAL-ADICUP3029 ARM Cortex-M3 controller, sold as part of the full ELCZ kit [verify see package contents]); evaluate with ADI example firmware / SensorPal tools and read data over the serial interface.
Any questions? Ask CelesteSM will help you find out quickly.
ADI EVAL-AD5941ELCZ Electrochemical & Impedance Measurement Evaluation Kit for the AD5941 Front End
The EVAL-AD5941ELCZ is Analog Devices' evaluation platform for the AD5941 a highly integrated, low-power analog front end built for precision electrochemical measurement: electrochemical impedance spectroscopy (EIS), potentiostat control, amperometric and voltammetric techniques. Instead of designing an excitation loop, TIA, ADC and switch matrix from scratch, you get the complete signal chain on one evaluation board, with BNC electrode connections and a custom micro-USB to alligator-clip cable, so you can be characterizing a real electrochemical cell the same afternoon it arrives.
Real EIS, from 0.015 Hz to 200 kHz. An on-board waveform generator and high-speed DAC produce sine excitation across the frequency band used in batteries, sensors and bio-impedance work. The AD5941's hardware DFT engine returns real and imaginary components directly no host-side FFT load while the dual excitation loops (low-bandwidth loop with low-power dual-output DAC and TIA, plus high-bandwidth loop), high-resolution ADC and programmable switch matrix cover voltage, current and impedance measurement in one device.
Engineered for honest electrochemistry. The board exposes a BNC electrode interface with an on-board calibration resistor and supports 2-wire or 4-wire cell connection use 4-wire for low-impedance cells (e.g., battery stacks) to eliminate lead and contact resistance error. Low-frequency points are necessarily slower (a 0.1 Hz measurement needs multiple full signal cycles expect tens of seconds per point), and the hardware is optimized for measurements above ~1 Hz [verify]; plan your sweep times accordingly.
A practical evaluation workflow. Stack the board onto an Arduino Uno form-factor controller (EVAL-ADICUP3029, ARM Cortex-M3 included in the full ELCZ kit [verify]), connect the cell via BNC or the alligator-clip cable, power over USB and run ADI's example firmware or SensorPal tools. Serial output lets you log impedance data directly for analysis.
Typical applications
- Battery / supercapacitor electrochemical impedance spectroscopy (EIS)
- Electrochemical gas and toxic-gas sensor development
- Skin and body (bio-) impedance measurement systems
- Corrosion research and electrochemical cell characterization
- Portable / wearable sensing front-end prototyping
Warranty & Returns
Warranty, Returns, And Additional Information
Warranty
- Please contact the Seller directly for warranty information. Warranty information may also be found on the Manufacturer's website.
- CONTACT
Return Policies
- Return for refund within: 30 days
- Return for replacement within: non-replaceable
- This item is covered by CoreDepot Return Policy
Manufacturer Contact Info
- For a directory of all our manufacturers, please click below.
- Manufacturers Directory









