Question 1

I have a 24in as my main and a 20in as my secondary, will this stand be able to hold the two without weight distribution issues?

Accepted Answer

I think this stand would be fine for your application.  With the sliders on the brackets you should be able to distribute the weight so it isn't an issue.  The stand is very stable I have two 22" monitors on mine and haven't ever had an issue.

Question 2

Will this stand work with my AOC i2267Fw Monitors?? I can't tell how the monitors mount...

Accepted Answer

Normally there are 4 holes in the back of your monitor, sometime behind the plate that attaches your monitor stand to the monitor.  You can see in the pic that there are two sets of 4 holes on each of the mounting plates .... the stand comes with screws for attaching and those holes should line up with one of the sets of holes on your monitor.  Check if your monitor is VESA Compliant.

Question 3

Will this stand work with a "Mfr. Part: S2340M / 29 UNSPSC: 52160000" Dell 23" monitor?

Accepted Answer

I would think it should, yes.  I have dual Asus 24" monitors on it now, and so long as the back of the monitor supports the standard screw configuration for a stand (which I have to imagine they all do by now), then it should be able to handle those monitors.  I'll add that the stand is very sturdy - with dual 24" monitors it still sits very stable on my desk.  I have additional lift under the stand, and even elevated it's still solid.  Hope that helps.

Question 4

After attaching monitors, I can adjust the height of them so I don't have to purchase a stand, correct?

Accepted Answer

Mark,

I am not exactly sure of your question, but if you are asking whether the monitors can be adjusted vertically, the answer is yes.  You can easily see how they adjust horizontally.  For vertical adjustment, the two arms slide up and down the post and lock into whatever height you select.  The arms also will rotate fore and aft so the monitors can sit at a comfortable angle to each other.  Mine are probably 15 degrees inward from flat.

You didn't ask but I would definitely purchase this monitor stand again.  It takes a little to get it where you want it, but it is worth the time and money.

Question 5

does this work with all monitors?

Accepted Answer

It should work with most flat panels as long as they are not larger than the size/capacity of the stand. The monitors also much have a VESA mount capability. Not all of them do. The low-budget LCD monitors often do not. (VESA refers to the square pattern with 4 screws that attach the display to the stand.)

Question 6

Does this clamp/screw to the desk or is it held down by gravity alone and use the distributed weight along the legs to stay stable?

Accepted Answer

gravity only - it works but you most use two monitors ( a given ) we have about twenty of these no issues to date.

Question 7

how far apart can the two monitors be placed?

Accepted Answer

The distance between monitors really depends on the size and orientation of the monitors you are using and the thickness of the bezel (frame) around them. I have two 24" Asus VE248H monitors mounted on my stand. I prefer to have them touching bezel to bezel, but I think at most there can be about 1/8" gap between them if I slide them apart as far as they can go. If the bezel around them was thicker, they might not have any gap at all. If I were to rotate one or both monitors into portrait mode instead of landscape (or use smaller monitors), I could have a much larger gap between them. I would not attempt to use any monitors larger than 24" (diagonal) on this stand.

Question 8

Can this mount have the monitors sit extremely low to where the monitors would touch the desk?

Accepted Answer

It is possible depending upon the size of the monitors and the orientation of the monitors.  For example, it would be possible if you had 2 - 24" monitors in rotated to portrait mode.  It would also probably be possible if you had 2 monitors smaller than the 24" maximum size.  However, it is not possible to have the bottoms of the monitors touching the desk surface if you have 2-24" monitors in landscape orientation.  At their innermost point, where the two monitors are nearest to the center of the monitor stand, then would touch the base of the monitor stand rather than going all of the way to the desk surface.  Having said that, the base of the monitor stand is only about 1 inch thick, so the bottom of your monitors would only be about 1 inch above the surface of the desk.

Question 9

I have 2 - Viewsonic VX2250wm-LED monitors with a VESA mount 100mm x 100mm, weight 7.1 lbs. One reviewer, Tony T. gave this stand a one star and said it did not work on LED monitors. I can't understand if it can handle the weight and has a VESA mount, why this would be a problem. Anyone using the Viewsonic monitors listed above?

Accepted Answer

This can hold LED's, LCD's thin or thick, very sturdy and needs some adjustments. I have 2 HP LV2311 monitors on it and it's very sturdy. The foot is very large and will take up some desktop. It's not very tall but just right for eyelevel. Takes a while to get used to the massive desktop with 2 monitors. VESA mounts are good and comes with screws. Hope this helps!

Question 10

What are the dimensions of the base? I only have limited amount of desk space and the other monitor stand I ordered had two large of a base.

Accepted Answer

The base is basically a "V" shape. I will discribe it to the best of my abilities.

Widest point: 16.5"
Narrowest point : 5.5"
Depth: 9.75" *Measured from the base of the "V" to the point between the two vectors that create a V

Brand	Planar
Model	997-5253-00
Type	Multi-Monitor Stand

Color	Black
Specifications	Supports two displays between 15.00" - 24.00" with maximum weight 26.00 lbs. per display Flexibility to tilt up and down +/- 20 degree Swivel displays side to side +/- 20 degree Rotate 90 degree for landscape or portrait mode Hole pitch 100 mm x 100 mm VESA and 75.00 mm x 75.00 mm VESA

Dimensions (H x W x D)	18.80" x 10.80" x 3.70"
Weight	7.95 lbs.

Best Sellers

Meet Your Seller

Sponsored Products

Planar 997-5253-00 Black Dual Monitor Stand for LCD Displays

Learn more about the Planar 997-5253-00

Customer Reviews of the Planar 997-5253-00

Warranty & Returns

Warranty, Returns, And Additional Information

Warranty

Return Policies

Manufacturer Contact Info

Item#: 9SIA6ZPK9V2026