Question 1

is it 10/100 or 10/100/1000?

Accepted Answer

It is a 10/100/1000 unmanaged switch

Question 2

What is the meaning of the term "unmanaged"?

Accepted Answer

On some hubs you can control or "manage" each or all of the ports. So maybe you want one port to have a higher or lower speed than another..or communicate  at different duplex settings. .. the "unmanaged" hub has no such individual port settings capabilities. ... if it has a built in automatic speed it will automatically set to 100 or 10 or 1000 me it's as needed but you usually don't have manual control over those settings

Question 3

My internet speed is only 75 Mbps, what is the benefit of having a Gigabit switch?

Accepted Answer

Short answer: not much. Longer answer: A Gigabit device will have lower latency than, say, a 100M device, so it will forward the packets faster. A switch, rather than a hub, will forward traffic based on its address rather than simply repeating it on all ports. Thus you could have several independent streams of packets running at full speed without interference on an 8-port switch: port 1 sending to a device on port 3, port 5 talking to itself, ... . And, of course, if you later add Gigabit devices they can run at full speed.

Question 4

Is that what I need to hook up computers to wired network?

Accepted Answer

If you are running a peer to peer Ethernet network between computers this will allow you to do so. You will of course have to set up the individual computers for peer to peer networking. This type of configuration will not allow you access to the internet.

If you wish to run a managed network, this switch is not the solution. For a manged network you will need a router of some kind. Depending on the router, most allow for static routing or DHCP operation and when combined with an ISP they will allow you access to the internet along with establishing your Ethernet LAN behind the router.

This switch is primarily for extending an existing Ethernet network either for increased distance between devices or for an increased number of devices.

Question 5

Can you remotely access, via team viewer or Remote Desktop, using this device?

Accepted Answer

Your question lacks context - there are not sufficient details to understand exactly what you are asking.  The device is a switch, and not a smart one, so it does not get assigned its own IP address, and it does not have a remote access interface for itself.  Therefore, if you are asking if you can access the switch itself remotely, the answer is no.  However, if you are asking if you can use team viewer or remote desktop to connect to machines that are connected to each other through this device, the answer is yes: it is not a router, it is a switch, and therefore it passes all traffic from the source port to the destination port when it comes to TCP communication between devices connected to this router.  I hope this answers whatever question you were trying to ask.

Question 6

Will my router's features still function as though I were using the ports on the back of it?

Accepted Answer

Yes, 
This type of switch is essentially invisible to your router.

Question 7

in my basement  i have 
-4 ethernet ports for different rooms (1 in office)
-and few devices which need hard wired internet
-i have a time capsule i plan to keep in 1st floor office and stream my wifi from there

will this switch work for me ?
modem-->switch-->ethernet in office-->time capsule-->wifi

Accepted Answer

Shopper:
This is a terrific gigabit switch, which has worked for us flawlessly for several years.  It should perform well in your application, however you will need to make sure that you have the DNS setup correctly as the WiFi router will have to assign addresses to your devices and the switch will also assign them.  Just need to make sure that there are no conflicts and you will be good to go.

Question 8

There are different kinds of CAT6 cables... Twisted Pair and some that don't specify, Stranded and Solid wires, and different wire gauges. I've also seen mention of CAT6a and CAT6e.  I'm looking to convert my entire network to new Netgear Gigabit products, with a GS108, two or three GS105, and a WAC510 Access Point, because I'm getting a new SRX5308 Gigabit Router that will replace an FSV338 that went bad and is being replaced under warranty.  The longest run will be 50ft to a GS105 , one 15ft to a GS108, and most others being 6ft.  What kind of cable should I get?

Accepted Answer

All CAT cables are twisted pairs UTP(unshilded) or STP (shilded). Average distanse for cables up to 100 feet. I run as far as 300 feet and had no essues.  Just get premade (with mail plug uttached) CAT-6 strended cables. Strended cables are more flexeble.

Question 9

Will this work outside US? Just want to confirm is there any Network norms to make it work outside US?

Accepted Answer

It works with standard network protocols. If your country can supply the correct input voltage you should be fine. Keep in mind this is an non manageable switch.

Question 10

Can this switch, GS108, be used to connect POE IP security cameras? 
I have 5 cameras that need a switch, run is there, old switch died.

Accepted Answer

This is fantastic ethernet switch.  For POE, you would have to provide separate power to each camera.

	GS105NA	GS105E	GS108	GS108E	GS116NA

Customer Reviews	—	—	—	—	—
Price	—	—	—	—	—
# Gigabit Ethernet Ports	5 x 1G	5 x 1G	8 x 1G	8 x 1G	16 x 1G
# PoE Ports	----	----	----	----	----
# SFP Fiber Ports	----	----	----	----	----
Management Type	Unmanaged	Plus	Unmanaged	Plus	Unmanaged
Management Layer	----	L2	----	L2	----
Advanced Network Features	----	Basic VLAN & QoS IGMP Storm Control Auto DoS	----	Basic VLAN & QoS IGMP Storm Control Auto DoS	----
Fanless Housing	?	?	?	?	?
Mounting Options	Desktop or Wall	Desktop or Wall	Desktop or Wall	Desktop or Wall	Desktop or Wall

	GS105NA	GS105E	GS108	GS108E	GS116NA

Customer Reviews	—	—	—	—	—
Price	—	—	—	—	—
# Gigabit Ethernet Ports	5 x 1G	5 x 1G	8 x 1G	8 x 1G	16 x 1G
# PoE Ports	----	----	----	----	----
# SFP Fiber Ports	----	----	----	----	----
Management Type	Unmanaged	Plus	Unmanaged	Plus	Unmanaged
Management Layer	----	L2	----	L2	----
Advanced Network Features	----	Basic VLAN & QoS IGMP Storm Control Auto DoS	----	Basic VLAN & QoS IGMP Storm Control Auto DoS	----
Fanless Housing	?	?	?	?	?
Mounting Options	Desktop or Wall	Desktop or Wall	Desktop or Wall	Desktop or Wall	Desktop or Wall

Brand	NETGEAR
Series	ProSafe
Model	GS108-400NAS
Switch Type	Others

Format	Desktop
Network Management Type	Unmanaged

Primary Ports	8 x RJ45
Primary Port Speed	10/100/1000Mbps

Netgear ProSafe GS108 8-Port Gigabit Ethernet Unmanaged Switch, GS108-400NAS

Compare Similar NETGEAR Switch Models

Compare Similar NETGEAR Switch Models

Learn more about the Netgear Inc. GS108-400NAS

Customer Reviews of the Netgear Inc. GS108-400NAS

Warranty & Returns

Warranty, Returns, And Additional Information

Warranty

Return Policies

Manufacturer Contact Info

MAC Address Table	4K
Switching Method	Store and Forward
Jumbo Frames	9KB
Buffer Memory	192KB

Protocols	TCP/IP
PoE	No
QoS	Yes
Layer	2
LEDs	Per port: Speed, Link, Activity Per device: Power Status

Temperature	Operating Temperature: 0 ~ 40 degree Celsius (32 ~ 104 degree Fahrenheit) Storage Temperature: -20 ~ 70 degree Celsius (-4 ~ 158 degree Fahrenheit)
Humidity	Operating Humidity: 90% maximum relative humidity, non-condensing Storage Humidity: 95% maximum relative humidity, non-condensing

Dimensions & Weight
Dimensions	1.10" x 6.20" x 4.00"
Weight	1.04 lbs.

Item#: 12K-008X-00026

Netgear ProSafe GS108 8-Port Gigabit Ethernet Unmanaged Switch, GS108-400NAS

Compare Similar NETGEAR Switch Models

Compare Similar NETGEAR Switch Models

Learn more about the Netgear Inc. GS108-400NAS

Customer Reviews of the Netgear Inc. GS108-400NAS

Warranty & Returns

Warranty, Returns, And Additional Information

Warranty

Return Policies

Manufacturer Contact Info