Pros: I received two of these drives to review, and tested them with both my custom built WHS and my ReadyNAS 312. Three things immediately apparent with these drives are : Their low power consumption (compared to standard desktop drives and laptop drives) and Because of the low power consumption, these drives run much cooler than standard drives. And lastly, these drives are very quiet. Average temperature in my ReadyNAS went from 42c to 34c (under heavy use). Power consumption went from ~35 watts to 30 watts. Similar results were observed in my WHS. Although the drives in the WHS are standard 7200 rpm drives so the power consumption reduced by about 10 watts. These observations can be attributed to the newest version of intellipower in these drives (lower power consumption, noise reduction, less heat generated) and the upgrade to NASware 2.0. 2 of these drives in raid 0 (and even raid 1) are more than enough to saturate gigabit ethernet for a home nas. Even single drive performance is very good even compared to other laptop drives (100+MB/s read/80+MB write). The new intellipower has been tuned for higher performance, while sacrificing nothing in power consumption and noise. Drives carry a 3 year warranty (a good thing considering drive warranties have been reduced over the past few years). Benchmarks of these drives can be found by a few different review sites and perhaps a few eggxperts will post some also. The bottom line is these drives perform quite well by today's standards for 2.5 inch drives - that's great considering the size of these drives (1TB) and power consumption and noise levels of these drives.

Cons: None on these drives, however the 1st gen Red desktop size drives have a bad reputation. Hopefully WD has learned what was wrong with those drives and has made a reliable quality product.

Overall Review: I was excited to see WD release the RED series drives in a 2.5 inch form factor. This will allow NAS devices to get to a MUCH smaller form factor - I am thinking my ReadyNAS could be about 1/3 of the size it is now (since it wouldn't have to accommodate 2 desktop size HDDs) and home server boxes in a much smaller form factor as well. With everything going to smaller form factors, these drives *should they prove to be reliable* will allow a shrinking of NAS/Home servers and allow an even lower power requirement as well. And with a lower power requirement, less cooling will be needed - which will also mean less noise as well.

Pros: Updating eggxpert review from 4-15-13.

Cons: After about 7 months, this drive has failed. About a month ago the drive was noticeably louder and today the drive has completely failed.

Overall Review: Sad to see such a failure with HDD warranties getting shorter these days...

Pros: Tested on AM5 and LGA 1700 (9800X3D & 12700K) for both rated speeds and timings for XMP and EXPO. Ran flawlessly at all advertised speeds for both on both systems and passed memtest as well. Low profile, should be fine ram for any air cooler or aio Never really got as warm as other DDR5 kits I have when in use - I didn't see temps above 50c No RGB - and I like the subdued look. The motherboard/ram/gpu looks great without it.

Cons: "Pro" and "Overclocking" seems to be just marketing terms. I couldn't get anything to post when increasing frequency while keeping the same general latency going above XMP 6400, nor could I get 6000 with lower latency stable below the rated CL36 with EXPO. To be fair - especially on AM5 - there isn't really any substantial gains from doing so beyond a statistical margin of error.

Overall Review: The plain look of my motherboard/ram/gpu with the contrast of the ARGB fans really grew on me over the time I was testing. I think I will carry this type of build going forward, leaving the "fun" to the fans and the "serious" to the components. Tested with the following systems (with this ram kit)- AM5 (not pictured) 9800X3D Asrock B650M-HDV/M.2 RTX 3060ti founders ID Cooling DX240 MAX Fractal pop air rgb LGA1700 I7 12700K MSI Z790 Tomahawk MAX RTX 3060ti founders (not pictured - swapped with an old GTX 950 for the picture as the gpu was borrowed from a different system) Arctic Liquid Freezer II 280 ARGB Lian Li O11 Vision

Pros: Pictures don't do this justice, this is a really nice looking case. 2! 5 1/4" bays Just enough room to route cables in the back Premium feel, nothing feels cheap or bends Plenty of airflow with the mesh front Built in ARGB controller The included 3 argb fans are average but do the job.

Cons: Mounting a 5 1/4 drive flush as pictured and as suggested in the build guide has the cover plate resting on the eject button and literally hitting my desk lightly means watching the drive open and popping that cover off. Either you have to mount it back a bit (which my OCD won't allow), or be careful when placing the cover on/off. RGB controller is lacking, plus I wish there was a cable included to sync the power button to the rest of the system Can be a bit tight in spots when building - make sure you build in the proper order (see other thoughts)

Overall Review: Ignore the build guide included with the system, install the power supply LAST. I had to remove half my build (since I had already done some cable managing) to get the front panel audio connected as there wasn't enough room to fit the connector past the power supply when it was installed. If air cooling, maybe move the front fans inside the system to allow for more airflow - having the fans pressed up against the mesh seems like it would constrain the flow a bit. ASUS TUF Gaming X570 Plus Wifi Ryzen 3900x RTX 3060ti FE Arctic Liquid Freezer ii 280 G Skill Trident Z (b die) OC Corsair RM 650

Pros: Plug and play with the LS100 Smart lighting kit Identical to the smaller strips included with the kit Great diffusion Great customization

Cons: Magnet VHB peels on both the expansion kit and starter kit were difficult. (see my review on the LS100 starter kit) Adding this expansion kit throws off the timing just a bit when using these on my ultrawide monitor when having the lights "chase" on the top and bottom. The top side was just a touch behind. This didn't happen with the initial install I did with just the starter kit. iCue doesn't seem to fully support using these for standard ultrawide monitors - the picture in the software shows an ultra-ultra wide for the 'Ultrawide' setting (like the 49" variety) with 2 short strips and 4 long strips and not my config of 4 short and 2 long. Maybe full support can be added for the more standard 34" ultrawides using this kit?

Overall Review: A great addition for the starter kit - especially for ultrawide monitors.

Pros: Just about perfect brightness Excellent diffusion Easy enough to install Completely customizable within iCue Can even be used without iCue (hardware profile) - but there's not as much customization

Cons: Magnet VHB peels didn't peel. There is a tab on every magnet and I needed to use a box cutter and poke under the peels to get them started. Just pulling it by the tab wouldn't start the peel. This was the most frustrating thing and why I deducted an egg. Magnets hold well enough, but could be stronger. iCue software was 1gb...

Overall Review: When setting this up make sure to read the instructions and start at the correct corner on the back of your monitor and work in the correct direction! Ultrawide monitors need additional strips for full coverage (LS100 expansion kit)