Specifications: Interfaces:
PoE IN:1 x 10/100/1000BASE-T Ethernet with IEEE 802.3at PoE "Data + DC power" in auto MDI/MDI-X, auto-negotiation RJ45 connector
PoE OUT: 2 x 10/100/1000BASE-T Ethernet with IEEE 802.3at/802.3af PoE "Data + DC power" out auto MDI/MDI-X, auto-negotiation RJ45 connector
Power over Ethernet
PoE Standard:
"PoE In" Port: IEEE 802.3at Power over Ethernet Plus end-span/mid-span PD class 4 PD
Per "PoE Out" Port:
IEEE 802.3at Power over Ethernet Plus end-span PSE
IEEE 802.3af Power over Ethernet end-span PSE
PoE Power Supply Type: End-span (Type A)
PoE Power:
"PoE In" Port: 52 - 56V DC, max. 30.8 watts
Per "PoE Out" Port: 44 - 55V DC, max. 25 watts
Power Pin Assignment:
"PoE In" Port: 1/2 (+), 3/6 (-); 4/5 (+), 7/8 (-)
Per "PoE Out" Port: 1/2 (+), 3/6 (-)
Data Rate: 10/100/1000Mbps
MAC Address Table: 2K
Data Bu...
Wireless Data Rates: Max bandwidths and peak data rate per band: 20/40 (2.4 GHz), 20/40/80 (5 GHz), 20/40/80/160 (6 GHz), and maximum peak data rate 3.9 Gbps
Frequency Band: 2.4 GHz and 5 GHz and 6 GHz
Interface: Wired network interface: 2 x 2.5GbE
Ports: E0, E1: Two Ethernet wired network ports (RJ-45); Autosensing link speed (100/1000/2500BASE-T) and MDI/MDX; 2.5Gbps speed complies with NBase-T and 802.3bz specifications; POEPD: 48Vdc (nominal) 802.3af/at/bt POE (class 3 or higher); 802.3az Energy Efficient Ethernet (EEE)
Ports: 1-port 10/100/1000Base-T RJ-45 with auto MDI / MDI-X function
2-port SFP slot interface, SFP supports 1000Base-X and 100Base-FX transceiver via DIP switch configured
LEDs: 3 x LED for System and Power:
Green: DC Power 1
Green: DC Power 2
Green: Power Fault
2 x LED for Per Copper Port:
Green: 1000 LNK / ACT
Orange:100 LNK / ACT
1 x LED for Per mini-GBIC interface (Port-1 and Port-2):
Green: LNK / ACT
Features: Adapter Features
Data Rate Supported: 100/50/25/10GbE per port
Bus Type/Bus Width: PCIe 4.0 x16
Note: full 200Gbps performance requires PCIe slot bifurcation enabled in the system BIOS
Hardware Certifications: BSMI, CE, CMIM, FCC, ICES, KCC, RCM, UKCA, cURus, and VCCI
BMSI RoHS and RoHS-compliant: Product is compliant with Taiwan Bureau of Standards, Metrology and Inspection (BMSI), and EU RoHS Directive 2 2011/65/EU (Directive 2011/65/EU) and its amendments (e.g. 2015/863/EU)
Controller: Intel® Ethernet Controller E810-CAM1 (two controllers per adapter)
Power Consumption
DAC's
100GbE (Typical Power) Max 21.8 W 29.6 W (Max Power)
Idle (no traffic) 19.2 W (Typical Power)
Optics
100GbE Max 25.3 W (Typical Power) 33.5 W (Max Power)
Idle (no traffic) 22.8 W (Typical Power)
QSFP28 Max Pow...
Specifications: Description: 8 Digital Inputs and 8 Digital Outputs
Digital Inputs: 8
Logic Level 0: -30.0V to +1.0V
Logic Level 1: +2.0V to +30V
Latched Inputs: Triggered by user programmable positive or negative edges, stays true until acknowledged
Counter Inputs: User progammable- counts positive or negative transitions up to 100Hz
Watchdog: Active high/low, Pulsed high/low
Digital Outputs: 8
Digital Output Type: Open drain transistor, protected MosFET. Short circuit protection up to 36V. Over temperature shutdown -175°C typical 150°C min
Maximum Output Load Voltage: 30 VDC
Maximum Output Current Sink: 0.85A per channel
Serial Gateway: RS485 NuDam/ADAM compatible gateway
Number of Ports: 1
Network Port Type: RJ45 Jack 10/100 MHz Autosensing, Cross Over Autosensing (MDIX)
Network Protocols: ICMP, IP, TCP, DHCP, HTTP
Protection: 1500V M...
Wireless Data Rates: Max bandwidths and peak data rate per band: 20/40 (2.4GHz), 20/40/80 (5GHz), peak data rate 1.49 Gbps, maximum data rate 1.78 Gbps
Wireless Data Rates: 802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps
802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps
802.11n data rates on 2.4 GHz: 6.5 to 300 Mbps (MCS0-MCS15, HT 20/40)
802.11ac data rates on 5 GHz: 6.5 to 867 Mbps (MCS0-MCS9)
Interface: 1x Gigabit Ethernet uplink (10/100/1000BASE-T autosensing), PoE
3x Gigabit Ethernet local ports (10/100/1000BASE-T), including one PoE out port: PoE out provides 802.3af (Class 0) when access point is powered by 802.3at, or no output when powered by 802.3af
One passive pass-through port, RJ-45 (back to bottom)
Frequency Band: Indoor range up to 50m (In ideal conditions)
Outdoor range up to 300m (In clear view and ideal conditions)
2 internal QWL omnidirectional antennas
Modulation: GFSK
Radio frequency range:
1880 MHz to 1900 MHz (EU)
1920 MHz to 1930 MHz (US)
1902 MHz to 1906 MHz (TH)
1910 MHz to 1920 MHz (BR)
Transmission power: Average 10mW
RX sensitivity: typ. -91dBm
Power: AC 100-240V Input and DC 5V/600mA Output
Features: Extending the DECT coverage
Supports automatic handover of calls between RT30
Up to 4 simultaneous calls per repeater
Up to 6 repeaters per base station
Up to 2 repeaters can be arranged in cascade (only when connected to W60B/W70B)
Auto association
Base Link Reset
LED Display:
LED 1 Power On
LED 2 DECT Link
LED 3 Active Relay
Compatible with Yealink W60B (version 77.81.0.35 or l...