Specifications: Kit Content:
1 x Country-specific power cord, IEC, 6 ft.
1 x Power adapter
Input: 100 - 240V AC, 50/60Hz 0.6A
Output: 12V DC 2.0A
AC plug: country-specific
DC plug: Right-angle, 2.5 x 5.5 x 10 mm (ID x OD x L) female, positive center
DC cable length 1.5m
Features: • Converts a non-PoE port to a PoE++ 10G port
• Supplies PoE (15.4W), PoE+ (30W), or PoE++ (90W)
• 10GBASE-T compliant
• Integrated power supply
• Network a PoE device up to 100m (328 ft.) over cat6a or better cabling
• Save on installation and equipment costs
• IEEE 802.3af, 802.3at, and 802.3bt compliant
Specifications: Dimensions: 7.73 x 3.68 x 1.28"
Weight: 0.63 lb.
Interface Connections:
1 x 1 Gbps SFP Port
1 x DC Terminal Block
1 x DC RJ45 Port DC Injection
1 x 1000 Mbps Ethernet PoE Port
Typical Power Consumption 1.5W
PoE Output: PoE RJ45 Port, 2-Pair (4, 5+; 7, 8-) (24V DC), or 4-Pair (24V DC or 50V DC) PoE
DC Output: Terminal Block, 2-Wire (24V DC or 50V DC)
Input DC Voltage: 16 to 57V
Specifications: PoE Standard: IEEE 802.3af (Power over Ethernet)
IEEE 802.3at (High Power over Ethernet)
PoE Power Supply Type: Mid-Span / Type B
PoE Power Output: 52V DC, 510 mA, Max. 26 watts
Power Pin Assignment: 4/5 (+), 7/8 (-)
Maximum Distance: 4 units, daisy-chain installation with 500m support
Data Rate: 10/100/1000 Mbps
Switch Architecture: Store-and-Forward
Maximum Frame Size: 1552 Bytes
Flow Control:
Back pressure for half-duplex
IEEE 802.3x pause frame for full-duplex
LED Indicators:
1 x PoE IN (Green)
1 x LAN Data (Green)
1 x PoE OUT (Green)
Power Requirements: IEEE 802.3at compliant with voltage within 52V-56V DC
Power Consumption: 3.2 watts (system maximum)
Specifications: Interface:
PoE (Power + Data) Input Port: 1 x RJ-45 STP
Data” Output Port: 1 x RJ-45 STP
DC Out Plug Connector: 1
LED Indicator System: PoE In x 1 (Green)
Network Cable:
10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
100Base-TX: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m (328 ft.)
EIA / TIA-568 100-ohm STP (100m)
Data Rate: 10/100/1000 Mbps (varies on Ethernet device attached)
DIP Switch: 12V DC / 24V DC output voltage
Power Input: 802.3at PoE+ 52 ~ 56V DC
PoE Standard: IEEE 802.3at High Power over Ethernet
Number of clients device can be powered: 1
Power Output:
12V DC, 2A max
24V DC, 1A max
Standards Compliance:
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3at...
Specifications: Standards:
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3ab
IEEE 802.3af
IEEE 802.3at
Device Interface:
1 x Gigabit PoE/PoE+ in port
1 x Gigabit PoE/PoE+ out port
1 x Power port (optional power adapter is not included)
LED indicators
Installation mounting points
Data Transfer Rate:
Ethernet: 10 Mbps (half duplex), 20 Mbps (full duplex)
Fast Ethernet: 100 Mbps (half duplex), 200 Mbps (full duplex)
Gigabit: 2000 Mbps (full duplex)
Power:
Powered by PoE/PoE+ Device
Consumption: 2 Watts (max.)
Specifications: Power consumption: 1.3 watts via POE
Forwarded PoE Power:
Up to 75 watts depending on standard
Maximum current 0.7 amps on data pairs
Maximum current 1.5 amps on spare pairs
PoE Standards:
IEEE 802.3af POE (15W) and IEEE 802.3at at POE Plus (2-event signature) (25-30W)
IEEE 802.3bt POE (to 75W)
Custom POE (incl. "always-on 48V" and "4-pair" POE)
Ethernet Interface:
Two independently auto-configuring 10/100 ports
(10Base-T / 100Base-TX, half / full duplex)
Patch or crossover cables supported
LEDs Status indicators:
Green LED - shows POE Power good
Yellow LED - shows Ethernet link / activity
Dimensions: 1.22" x 8.27" x 1.97"
Weight: 0.23 lb.
Mounting: 2/4 Bolt 7mm mounting holes. On 50/60mm centres
Operating temperature: -40 degree C to 70 degree C [-40 degree F to 158 degree F]
Relative humidity: Up to 85%, non-condensi...