Specifications: Standards:
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3ab
IEEE 802.3af
IEEE 802.3at
Device Interface:
1 x Gigabit PoE/PoE+ in port
1 x Gigabit PoE/PoE+ out port
1 x Power port (optional power adapter is not included)
LED indicators
Installation mounting points
Data Transfer Rate:
Ethernet: 10 Mbps (half duplex), 20 Mbps (full duplex)
Fast Ethernet: 100 Mbps (half duplex), 200 Mbps (full duplex)
Gigabit: 2000 Mbps (full duplex)
Power:
Powered by PoE/PoE+ Device
Consumption: 2 Watts (max.)
Specifications: Dimensions: 7.73 x 3.68 x 1.28"
Weight: 0.63 lb.
Interface Connections:
1 x 1 Gbps SFP Port
1 x DC Terminal Block
1 x DC RJ45 Port DC Injection
1 x 1000 Mbps Ethernet PoE Port
Typical Power Consumption 1.5W
PoE Output: PoE RJ45 Port, 2-Pair (4, 5+; 7, 8-) (24V DC), or 4-Pair (24V DC or 50V DC) PoE
DC Output: Terminal Block, 2-Wire (24V DC or 50V DC)
Input DC Voltage: 16 to 57V
Specifications: Cable Type: SFP+
Cable Length: 9.84 ft.
Connector on First End: 1 x SFP+ Network
Connector on Second End: 1 x SFP+ Network
Data Transfer Rate: 1.25 GB/s
Compatibility: Aruba 8320 Switch Series
Features: • Converts a non-PoE 2.5G port to a PoE++ 2.5G port
• Supplies PoE (15.4W), PoE+ (30W), or PoE++ (90W)
• Network a PoE device up to 100m (328 ft.)
• Integrated power supply
• 2.5GBASE-T compliant
• IEEE 802.3af, 802.3at, and 802.3bt compliant
Specifications: Cable Type: Twinaxial
Cable Length: 4.92 ft
Connector On First End: 1 x SFP+ Network
Connector On Second End: 1 x SFP+ Network
Device Supported: Network Device
Data Transfer Rate: 1.25 GB/s
Specifications: Interface:
PoE (Power + Data) Input Port: 1 x RJ-45 STP
Data” Output Port: 1 x RJ-45 STP
DC Out Plug Connector: 1
LED Indicator System: PoE In x 1 (Green)
Network Cable:
10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
100Base-TX: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328 ft.)
1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m (328 ft.)
EIA / TIA-568 100-ohm STP (100m)
Data Rate: 10/100/1000 Mbps (varies on Ethernet device attached)
DIP Switch: 12V DC / 24V DC output voltage
Power Input: 802.3at PoE+ 52 ~ 56V DC
PoE Standard: IEEE 802.3at High Power over Ethernet
Number of clients device can be powered: 1
Power Output:
12V DC, 2A max
24V DC, 1A max
Standards Compliance:
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3at...
Specifications: Cable Type: Fiber Optic
Cable Length: 3.28 ft
Connector on First End: 1 x SFF-8431 SFP+
Connector on Second End: 1 x SFF-8431 SFP+
Device Supported: Network Device
Compatibility: Cisco 10GBASE SFP+ Modules
Certifications & Standards:
MSA
ELV
Specifications: PoE Standard: IEEE 802.3af (Power over Ethernet)
IEEE 802.3at (High Power over Ethernet)
PoE Power Supply Type: Mid-Span / Type B
PoE Power Output: 52V DC, 510 mA, Max. 26 watts
Power Pin Assignment: 4/5 (+), 7/8 (-)
Maximum Distance: 4 units, daisy-chain installation with 500m support
Data Rate: 10/100/1000 Mbps
Switch Architecture: Store-and-Forward
Maximum Frame Size: 1552 Bytes
Flow Control:
Back pressure for half-duplex
IEEE 802.3x pause frame for full-duplex
LED Indicators:
1 x PoE IN (Green)
1 x LAN Data (Green)
1 x PoE OUT (Green)
Power Requirements: IEEE 802.3at compliant with voltage within 52V-56V DC
Power Consumption: 3.2 watts (system maximum)
Specifications: xDirect232 Single Port RS232 10/100 Device Server
Serial Connectors: Single-port: DB9F RS232 (DCE Pinned)
Ethernet Interface: 10/100M RJ-45
Serial Interface Baud Rate: 300bps to 921.6 Kbps
LED Indicators: Power/Status, Link, Activity, Serial RX Activity & TX Activity
CPU: Based on DSTni-EX Enhanced 16-bit x86 Architecture
Memory: 256 KB SRAM, 1 MB Flash
100-240 VAC International Power Supply with Regional Adapters.
Specifications: Description: 8 Digital Inputs and 8 Digital Outputs
Digital Inputs: 8
Logic Level 0: -30.0V to +1.0V
Logic Level 1: +2.0V to +30V
Latched Inputs: Triggered by user programmable positive or negative edges, stays true until acknowledged
Counter Inputs: User progammable- counts positive or negative transitions up to 100Hz
Watchdog: Active high/low, Pulsed high/low
Digital Outputs: 8
Digital Output Type: Open drain transistor, protected MosFET. Short circuit protection up to 36V. Over temperature shutdown -175°C typical 150°C min
Maximum Output Load Voltage: 30 VDC
Maximum Output Current Sink: 0.85A per channel
Serial Gateway: RS485 NuDam/ADAM compatible gateway
Number of Ports: 1
Network Port Type: RJ45 Jack 10/100 MHz Autosensing, Cross Over Autosensing (MDIX)
Network Protocols: ICMP, IP, TCP, DHCP, HTTP
Protection: 1500V M...
Specifications: Hardware Version: 2
Interface:
"Data" Input Ports: 4 x RJ-45
"Data+Power" Output Ports: 4 x RJ-45
Data Rate: 10/100/1000 Mbps
LED:
System: Power x 1 (Green)
Per PoE Port: PoE ready / in-use x 4 (Green)
Network Cable:
10Base-T: 4-Pair UTP Cat. 5 up to 100m (328 ft.)
100Base-TX: 4-Pair UTP Cat. 5 up to 100m (328 ft.)
1000Base-T: 4-Pair UTP Cat. 5e, 6, up to 100m (328 ft.)
EIA/TIA- 568 100-ohm STP (100m, 328 ft.)
Power Requirements: DC 52V~56V
PoE Power Supply Type: Mid-Span
PoE Power Output: Per Port DC 52V 30.8 watts / 15.4 watts
Power Pin Assignment: 4/5(+), 7/8(-)
PoE Power Budget: 120 watts
Number of 802.3af PD Class 0, 1, 2, 3 can be powered: 4
Number of 802.3at PD Class 1, 2, 3 can be powered: 4
Number of 802.3at PD Class 0, 4 can be powered: 4
Standards Compliance:
IEEE 802.3 10Bas...
Specifications: What's in the box:
Digi Connect EZ Mini - serial server, 1-port, with accessories
Power supply - 12 V, 2.5 A (76000823)
DIN rail clip (76002095)
Features: • Hardened IP30 rated Gigabit PoE++ Injector
• PoE (15.4W), PoE+ (30W), or PoE++ (90W) power
• Network a PoE device located up to 100m (328 ft.) away
• Extreme -40 to 75 °C (-40 to 167 °F) operating temperature range
• Redundant power inputs with overload current protection
• Includes DIN-rail mount and wall mount
• Power supply sold separately (model TI-S15052,
Specifications: Standards
802.3 10BaseT
802.3u 100BaseT
802.3ab Gigabit Ethernet
Proprietary PoE
Physical Interface
1) Gigabit Data Port
(1) Gigabit Data & Power Output Port
(1) IEC-320 C6 AC Connector
Power
Input voltage : 100 to 240 VAC
Input current: 0.8A maximum for 100 VAC
AC input Frequency: 47-63Hz
Maximum output power: 32.8W
Pin4, 5:54V; Pin7, 8: Return
Temperature Range
Operating: 32 degree F to 104 degree F (0 degree C to 40 degree C)
Storage: -22 degree F to 176 degree F (-30 degree C to 80 degree C)
Humidity (non-condensing)
Operating: 5 to 90% or less
Storage: 5 to 90% or less
LED Indicator: 1 x Power on Green
Mounting: Wall (anchors & screws included)
Dimensions: 1.30" x 3.90" x 2.27"
Parts: Manufacturers Limited Warranty: 1 Year / Parts Only
Specifications: Cable Type: Fiber Optic
Cable Length: 6.56 ft
Connector on First End: 1 x SFP+ Network
Connector on Second End: 1 x SFP+ Network
Conductor: Copper
Device Supported: Network Device
Specifications: Hardware Version: 4
Interface:
Data Input Ports: 24 x RJ45
Data + Power Output Ports: 24 x RJ45
Management Port: 1 x RJ45; 10/100/1000BASE-T, auto-negotiation, auto-MDI/MDIX
Data Rate: 10/100/1000 Mbps
LED:
System:
1 x SYS PWR (Green)
1 x PoE1 Fail (Red)
1 x PoE2 Fail (Red)
1 x Fan1 Fail (Red)
1 x Fan2 Fail (Red)
Per PoE Port: 1 x PoE-in-Use (Green)
2 x Management port: 1000 (Green), 10/100 (Orange)
Network Cable:
10BASE-T: 4-pair UTP Cat5 up to 100m (328 ft.)
100BASE-TX: 4-pair UTP Cat5 up to 100m (328 ft.)
1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m (328 ft.)
EIA/TIA- 568 100-ohm STP (100m)
Power Requirements: 100-240V AC, 50/60 Hz, 8A
Power Consumption: 800 watts max.
Cooling: 3 x Fan
PoE Power Supply Type: Mid-span
PoE Power Output: Per port DC 50-57V 30.8 / 15.4 watts
Power Pin Assignment...