Question 1

how do you change the colors? Would I be able to control the colors with my Gigabyte Z170x Gaming 3 mobo?

Accepted Answer

The LED strips connect to the LEDs that are preinstalled in the case and can be changed with a button on the front of the case. The lights do NOT interface with mobo unless your mobo has an "RGB Header". if your mobo has an RGB header...the lighting strips will need to be connected to that and controlled through mobo RGB software. I have an ASUS board that does not have an RGB header but through the software I am able to sync the mobo and GPU colors with the 10 case default colors pretty seamlessly. Hope this helps! Make sure you connect the strips to the preinstalled RGB connector in the cable management portion of the case. This case rocks and i highly recommend getting it. The case may be larger than expected because it supports full custom liquid cooling so be aware of that.

Question 2

My motherboard is an ASRock b450m and it has an "RGB LED Header", My case doesn't have an RGB switch or controller. Is there software so I can control these or what? I heard people way I need to download my motherboard manufacture software to control the RGB. Thanks :D
p.s. my motherboard connected is a 4 pin connector called "ADDR_LED1" if that helps :D

Accepted Answer

This comes with a adapter for 4 pin. That's how mine is hooked up and it works great. Only problem is some of leds went out after 6 months. But contacted Phanteks and they sent me more free of charge. A+++

Question 3

how do i get the rgb to cycle instead of just flash one color?

Accepted Answer

There's two different ways that I know of as I have two of these cases in the lightstrips both act different if you hold the button down until right before it shuts off and let go it should start cycling on my other case I have to wait for it to shut off and then hold the button down and let go after like 2 seconds

Question 4

what do i connect them to if i don thave and aura sync mobo?

Accepted Answer

I personally couldn't use them because I didn't have the right connection. Might have to get a +12V converter of some type.

Question 5

It says that it is Aura compatible, will it work with the new Asus strix cards?

Accepted Answer

It will as long as u plug in both strip and the card to the asus mobo because aura only support asus mobo then you can control the lights from the software or you need a phantek case for the strip to work

Question 6

Can these and the Halos be controlled by the Corsair CL-90111110-WW fan/rgb controller through the Link software?
My motherboard doesn't have any rgb headers and I'm not sure if the tempered glass Enthoo Pro M has any way to add rgb, it is unclear where those pins are in the case so I don't know for sure.

Accepted Answer

No the Corsair Commander Pro (CL-90111110-WW) controls 3-pin Addressable RGB strips these are 4-pin Non--Addressable RGB strips.

Question 7

I'm buying the p400s which has an included 300mm led strip included. Can I hook 400mm ones to it or do they have to be 300mm? Can they all be powered from one RGB header on my Asus motherboard?

Accepted Answer

You'll be able to either plug in to the included LED strip on the P400S (that way it's linked with the color switch button on the front of case which controls the included LED strip) or hook it up to the Asus motherboard.  From what I recall, you may need a 4-pin extension to reach the motherboard connector.

Question 8

Can these display multiple colors at the same time? I would be using these with Mystic Light on my rgb ready MSI M7 x470 motherboard.

Accepted Answer

No. The strips only emit one solid color. There work well though. Very happy with mine.

Question 9

Will this work with the Gigabyte B360 HD3?  That motherboard uses RGB Fusion and does have a RGB header.

Accepted Answer

It should work.

Question 10

What effects do these have?

Accepted Answer

It depends on the software that you install on it. They work fine with Asus Aura

Questions & Answers