Features: Higher Availability
Provides utility power to attached equipment when switched to maintenance bypass mode.
Allows UPS maintenance or replacement of the UPS without discontinuing power to critical equipment.
Flexibility
Easily installed - the UPS and utility power are both connected to the MicroPOD with the supplied cords.
Allows scheduled UPS maintenance to ensure continuous uptime without having to shut down protected equipment.
Rotary switch with indicators make the unit simple to operate.
Plug-and-play connectability for both input and output.
Compatible with any brand of UPS system.
Lowest Total Cost Of Ownership
Assures system uptime during maintenance activities.
Extreme affordability.
Internal Ports: 2 x M.2 (NGFF)
PCIe v3.0 or PCIe v2.0 x4 (4 lanes)
Operating Systems Supported: Windows 7/8/8.1/10, or Linux
Specifications: Primary M.2 Type: NVMe or AHCI SSD using M Key only
Secondary M.2 Type: SATA SSD using B Key
M.2 size: Length support 22x42mm, 22x60mm or 22x80mm
Internal Interface: 2 x M.2 (NGFF)
PCIe Interface: PCIe v3.0 or PCIe v2.0 x4 (4 lanes)
Power: PCIe Bus powered (3.3V)
Operating Systems Supported: Available system board PCIe x4 or x8 or x16 slot
Optional: 5V RGB header (3-pin)
OS support like Windows 7/8/8.1/10, or Linux
For booting, requires UEFI System Board and latest OS
Specifications: Interfaces
Serial
4 x Programmable Bi-directional RS-232/422/485 Port
(4 x DB9 Male Connector, configurable via pin assignments);
Baud Rate: 300 to 115200 (default: 9600);
Data Bit: 8 (default) or 7;
Stop Bit: 1 (default) or 2;
Parity: None (default), Even or Odd;
Flow Control: None (default) RTS/CTS
Ethernet
1 x RJ-45 Female, 10/100Base-T
Supported Protocol: ICMP, TCP/IP, DHCP, HTTPS, SSH
DHCP-enabled. The following default IP settings will be used if no IP is assigned within 30 seconds:
IP: 192.168.0.60
Subnet Mask: 255.255.255.0
Switches
Controller ID: 1 x 16-segment Switch
Expander ID: 1 x 8-segment Switch
Reset Button: 1 x Semi-recessed Pushbutton
USB: 1 x USB Type A
Power: Consumption 5 VDC, 7.5 W(adapter) ; 48VDC, 9.5 W(PoE, PoE 802.3 AF/AT compatibility)
Connectors: Connector A: 1 x VGA (14 pin, High Density D-Sub) Male
Connector B: 1 x USB Type-A (4 pin) USB 2.0 Male / 1 x VGA (15 pin, High Density D-Sub) Male
Specifications: Interfaces
Relay
8 normally open relays (8 x 2-pole terminal block)
Contact Rating: Max 24 VDC, 2A
Ethernet
1 x RJ-45 Female, 10/100Base-T
Supported Protocol: ICMP, TCP/IP, DHCP, HTTPS, SSH
DHCP-enabled. The following default IP settings will be used if no IP is assigned within 30 seconds:
IP: 192.168.0.60
Subnet Mask: 255.255.255.0
Switches
Controller ID: 1 x 16-segment Switch
Expander ID: 1 x 8-segment Switch
Reset Button: 1 x Semi-recessed Pushbutton
USB: 1 x USB Type A (Firmware upgrade only)
Power
Consumption 5 VDC, 10 W (Adapter); 48 VDC, 13 W (PoE, PoE 802.3 AF/AT compatibility)
Output 12 VDC, 300 mA