BEST SELLERS

In Thermal Compound / Grease

This thermal paste is easy to apply. Customer service was very helpful and quick. It is a great Arctic product. My CPU temp dropped almost 5˚C and the fans are much quieter.

The Thermal Grizzly Kryosheets are supposed to help increase cooling and you do not have to worry about re-pasting your cpu/cooler in a few years. Apply once and you're done. No oozing, no mess to clean up, I like that I can use one sheet and never have to worry about pulling the cooler off. I personally do not know if it's helping to keep temps down or not, I have seen several reviews where Kryosheet is lowering temps by around 2~4C but I cannot confirm. It's easy to use, you might need to trim a little material off so use very sharp scissors, it does slide a little but once you get it centered you're good to go.

Easy to use. Stays in place. Appears to work much better than expected, pleasantly surprised.

- easy instructions to follow to apply the correct amount of thermal paste - higher viscosity than your typical "grey" paste - wipes really helped to clean up the old caked on mess from my last application, over 6 years ago

Best thermal cleaner and prep.

easy to use one and done temps on par with kryonaut

i got a 20g from here and 1 from aliexpress and the one from there was obviously opened and it felt wetter, im not sure, but ill be buying from here next time.

Pros: Affordable: It strikes a great balance between cost and performance, making it a solid option for budget-conscious users. Easy to Apply: The paste has a smooth consistency, making it easy to spread and apply without making a mess. Reliable Cooling: Provides good cooling performance for average use, especially in mid-range builds or systems with moderate workloads. Non-Conductive: Safe for use on electronic components without the risk of electrical short circuits.

this product did what it was supposed to do

Ok first time i ever modded a GPU(msi 3090 ventus) and used Thermal putty and I used videos on youtube and AI to guide me and well i made big mistakes, first thing to know is this putty is very very soft, it falls apart so if you think you are going to make logs and move them onto the components it will rip apart, i used little spatula's and things to shape it glopped on. I got bad advice from a AI saying to use only certain amount, pre-flatten etc which was probably meant for that really dense other brand because first time I loaded up it refused to boot, nothing was making contact. It says you should only need 20g to 30g but I used the entire 100g and barely had enough, used to much on backplate side i guess because some squeezed out the X bracket area, had to salvage some from places like that and taking from other mounts to make bigger mounts, I'm sure I probably have parts not connecting still or messed up, PTM i messed up bad because i had to reopen ripped it up,redid that and put it together and boom loaded up! So was it worth a day of exhaustion and stress? YES! average 15 - 20c cooler, instant heat cooldown, Clock never throttles, temperate before hitting 90c on AI generation now low both in benchmarks and gaming the most notable thing is this ZERO STUTTERING, no hitching etc, it operates at specs and is much better than brand new I see people using syringes to use it, would have got some before I did this. Its hard af to work with and melts in your hands

This had my expectations high and it was a bit of a long wait but well worth it. This beat the MX-4 I had previously by over 10 degree Celsius. I even ran this compound on PRIME95 for over 10 hours and it never broke over 160 C. I am using a Corsair H60 and two Noctua Industrial Fans @ 3000rpms. Even before, the configuration was the same except the DX-1 and it is still going strong as I type this with my overclock of 4.7 GHZ // idle // @38 C. ~ 4.7 GHZ // full-load // @ 50 C . Also note that my idle is kind of high due to all the power-saving features of the CPU are shut off in the BIOS, so the temps would be much much lower if they were enabled. Excellent thermal paste, would buy again in the future.